LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2019 >> Highlander LE Plus, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 13 (Engine Mechanical (2GR-FE) (Service Information) (Except Hybrid) (1 Of 2)) >> Camshaft >> Removal [12/2013 - 11/2016] >> Procedure

Removal [12/2013 - 11/2016]: Procedure

WARNING: This page is about a different car, the 2016 Toyota Highlander, 2015 Toyota Highlander, and 2014 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL ENGINE TO ENGINE STAND 

    Refer to REMOVAL [12/2013 - 11/2016] 

  2. REMOVE ENGINE HANGERS 

    See step  83

  3. REMOVE IGNITION COIL ASSEMBLY 

    Refer to PROCEDURE - Step 2

  4. REMOVE INTAKE MANIFOLD 

    Refer to REMOVAL [12/2013 - 11/2016]

  5. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: Front Catalyst) 

    Refer to PROCEDURE - Step 7

  6. REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE 

    See step  8

  7. REMOVE NO. 2 MANIFOLD STAY 

    Refer to PROCEDURE - Step 14

  8. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR 

    Refer to PROCEDURE - Step 13

  9. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: Front Catalyst) 

    Refer to PROCEDURE - Step 3

  10. REMOVE ENGINE MOUNTING BRACKET RH 

    See step  13

  11. REMOVE GENERATOR ASSEMBLY 

    Refer to PROCEDURE - Step 6

  12. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY 

    See step  15

  13. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE 

    Refer to PROCEDURE - Step 22

  14. REMOVE NO. 2 TIMING GEAR COVER 

    See step  16

  15. REMOVE WATER PUMP PULLEY 

    See step  17

  16. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY 

    See step  18

  17. REMOVE NO. 1 VACUUM SWITCHING VALVE 

    See step  19

  18. REMOVE CRANKSHAFT POSITION SENSOR 

    Refer to PROCEDURE - Step 2

  19. REMOVE NO. 1 OIL PIPE 

    Refer to PROCEDURE - Step 14

  20. REMOVE OIL PIPE 

    Refer to PROCEDURE - Step 15

  21. REMOVE CRANKSHAFT PULLEY 

    See step  2

  22. REMOVE OIL COOLER ASSEMBLY (w/ Oil Cooler) 

    Refer to PROCEDURE - Step 4

  23. REMOVE NO. 1 OIL COOLER BRACKET (w/ Oil Cooler) 

    Refer to PROCEDURE - Step 21

  24. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET LH 

    Refer to PROCEDURE - Step 23

  25. REMOVE WATER INLET HOUSING 

    Refer to PROCEDURE - Step 27

  26. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 25

  27. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 26

  28. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 28

  29. REMOVE OIL STRAINER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 29

  30. REMOVE OIL PAN SUB-ASSEMBLY 
    1. Remove the 16 bolts and 2 nuts.
      GTY592004Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A Type A
      *B Type B
      *a Nut

      HINT: 

      Be sure to clean the bolts and stud bolts and check the threads for cracks or other damage.

    2. Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly with a screwdriver.
      GTY442341Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      NOTE:

      Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.

      HINT: 

      Tape the screwdriver tip before use.

    3. Remove the 2 O-rings.
      GTY295914Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  31. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 2

  32. REMOVE TIMING CHAIN CASE OIL SEAL 

    Refer to PROCEDURE - Step 3

  33. SET NO. 1 CYLINDER TO TDC/COMPRESSION 

    Refer to PROCEDURE - Step 37

  34. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY 

    Refer to PROCEDURE - Step 38

  35. REMOVE CHAIN TENSIONER SLIPPER 

    Refer to PROCEDURE - Step 39

  36. REMOVE CHAIN SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 40

  37. REMOVE IDLE SPROCKET ASSEMBLY 

    Refer to PROCEDURE - Step 41

  38. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1) 
    1. While raising the No. 2 chain tensioner assembly, insert a 1.0 mm (0.0394 in.) diameter pin into the hole to secure the No. 2 chain tensioner assembly.
      GTY445011Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Pin
      *b Plunger
      *c Push
    2. Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
      GTY426702Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Turn
      *b Hold
      • SST: 09922-10010 
      NOTE:
      • Be careful not to damage the cylinder head sub-assembly RH with SST.
      • Do not loosen the other bolts. If any of the bolts is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.
    3. Remove the 2 bolts, camshaft timing gear assembly and camshaft timing exhaust gear assembly together with the No. 2 chain sub-assembly.
  39. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY 
    1. Remove the bolt and No. 2 chain tensioner assembly.
      GTY136423Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  40. REMOVE CAMSHAFT BEARING CAP (for Bank 1) 
    1. Check that the camshaft and No. 2 camshaft are positioned as shown in the illustration.
      GTY436796Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Knock Pin
      *b Front View
    2. Uniformly loosen and remove the 8 bolts in several steps in the order shown in the illustration.
      Fig 1: Loosening Sequence Of Camshaft Bearing Cap Bolts (For Bank 1) (1 Of 2)
      GTY423728Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Uniformly loosen and remove the 12 bolts in several steps in the order shown in the illustration.
      Fig 2: Loosening Sequence Of Camshaft Bearing Cap Bolts (For Bank 1) (2 Of 2)
      GTY426899Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Uniformly loosen the bolts while keeping the camshaft and No. 2 camshaft level.

    4. Remove the 5 camshaft bearing caps.
  41. REMOVE CAMSHAFT 
    1. Remove the camshaft.
  42. REMOVE NO. 2 CAMSHAFT 
    1. Remove the No. 2 camshaft.
  43. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH 
    1. Remove the camshaft housing sub-assembly RH by prying between the cylinder head sub-assembly RH and camshaft housing sub-assembly RH with a screwdriver.
      GTY444218Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      NOTE:

      Be careful not to damage the contact surfaces of the cylinder head sub-assembly RH and camshaft housing sub-assembly RH.

      HINT: 

      Tape the screwdriver tip before use.

  44. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2) 
    1. While pushing down the No. 3 chain tensioner assembly, insert a 1.0 mm (0.0394 in.) diameter pin into the hole to secure the No. 3 chain tensioner assembly.
      GTY451307Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Pin
      *b Plunger
      *c Push
    2. Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
      GTY445608Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Turn
      *b Hold
      • SST: 09922-10010 
      NOTE:
      • Be careful not to damage the cylinder head sub-assembly LH with SST.
      • Do not loosen the other bolts. If any of the bolts is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.
    3. Remove the 2 bolts, camshaft timing gear assembly and camshaft timing exhaust gear assembly together with the No. 2 chain sub-assembly.
  45. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY 
    1. Remove the bolt and No. 3 chain tensioner assembly.
      GTY145648Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  46. REMOVE CAMSHAFT BEARING CAP (for Bank 2) 
    1. Check that the No. 3 camshaft and No. 4 camshaft are positioned as shown in the illustration.
      GTY439089Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Knock Pin
      *b Front View
    2. Uniformly loosen and remove the 8 bolts in several steps in the order shown in the illustration.
      Fig 3: Loosening Sequence Of Camshaft Bearing Cap Bolts (For Bank 2) (1 Of 2)
      GTY453761Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Uniformly loosen and remove the 13 bolts in several steps in the order shown in the illustration.
      Fig 4: Loosening Sequence Of Camshaft Bearing Cap Bolts (For Bank 2) (2 Of 2)
      GTY433258Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Uniformly loosen the bolts while keeping the No. 3 camshaft and No. 4 camshaft level.

    4. Remove the 5 camshaft bearing caps.
  47. REMOVE NO. 3 CAMSHAFT 
    1. Remove the No. 3 camshaft.
  48. REMOVE NO. 4 CAMSHAFT 
    1. Remove the No. 4 camshaft.
  49. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH 
    1. Remove the camshaft housing sub-assembly LH by prying between the cylinder head sub-assembly LH and camshaft housing sub-assembly LH with a screwdriver.
      GTY436468Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      NOTE:

      Be careful not to damage the contact surfaces of the cylinder head sub-assembly LH and camshaft housing sub-assembly LH.

      HINT: 

      Tape the screwdriver tip before use.

scientia non olet · About LEMON Manuals