Installation [08/2016 - ]: Procedure

INSTALL REAR SEAT BELT RETRACTOR COVER LH
1. Attach the claw to install the rear seat belt retractor cover LH.

INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

Align the 2 claws with the seat belt positioning holes, and install the retractor of the rear No. 1 seat outer belt assembly LH with the 2 bolts as shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*1	Bolt (A)
*2	Bolt (B)

for bolt A

Torque: 12.5 N*m (127 kgf*cm, 9 ft.*lbf)

for bolt B

Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)

INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH
Refer to PROCEDURE - Step 23 [10/2015 - 08/2017] , or refer to PROCEDURE - Step 23 [08/2017 - ]
INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
Refer to PROCEDURE - Step 26 [10/2015 - 08/2017] , or refer to PROCEDURE - Step 26 [08/2017 - ]
INSTALL DECK TRIM SERVICE HOLE COVER
Refer to PROCEDURE - Step 28 [10/2015 - 08/2017] , or refer to PROCEDURE - Step 28 [08/2017 - ]
CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH
1. Connect the shoulder anchor of the rear No. 1 seat outer belt assembly LH with the bolt.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
2. Check that the rear No. 1 seat outer belt assembly LH is not twisted.
3. Connect the floor anchor of the rear No. 1 seat outer belt assembly LH with the bolt.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
4. Check that the rear No. 1 seat outer belt assembly LH is not twisted.
INSTALL SEAT BELT ANCHOR COVER CAP
1. Attach the guide and 2 claws to install the seat belt anchor cover cap.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
Refer to PROCEDURE - Step 29 [10/2015 - 08/2017] , or refer to PROCEDURE - Step 29 [08/2017 - ]
INSTALL REAR DOOR SCUFF PLATE LH
Refer to PROCEDURE - Step 31 [10/2015 - 08/2017] , or refer to PROCEDURE - Step 31 [08/2017 - ]
INSTALL REAR SEAT ASSEMBLY LH
Refer to INSTALLATION [08/2016 - ]
INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (for Full Size Spare Tire)
Refer to PROCEDURE - Step 38 [10/2015 - 08/2017] , or refer to PROCEDURE - Step 38 [08/2017 - ]
INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (for Compact Spare Tire)
Refer to PROCEDURE - Step 38 [10/2015 - 08/2017] , or refer to PROCEDURE - Step 38 [08/2017 - ]
INSTALL REAR DECK TRIM COVER (for Full Size Spare Tire)
Refer to PROCEDURE - Step 40 [10/2015 - 08/2017] , or refer to PROCEDURE - Step 40 [08/2017 - ]
INSTALL REAR FLOOR FINISH PLATE (for Compact Spare Tire)
Refer to PROCEDURE - Step 39 [10/2015 - 08/2017] , or refer to PROCEDURE - Step 39 [08/2017 - ]
INSTALL REAR NO. 3 FLOOR BOARD
Refer to PROCEDURE - Step 41 [10/2015 - 08/2017] , or refer to PROCEDURE - Step 41 [08/2017 - ]
INSTALL REAR NO. 2 FLOOR BOARD
HINT:

Use the same procedure described for the No. 3 rear floor board side.
INSTALL DECK FLOOR BOX LH
Refer to PROCEDURE - Step 43 [10/2015 - 08/2017] , or refer to PROCEDURE - Step 43 [08/2017 - ]
INSTALL DECK BOARD ASSEMBLY (for Full Size Spare Tire)
Refer to PROCEDURE - Step 44 [10/2015 - 08/2017] , or refer to PROCEDURE - Step 44 [08/2017 - ]
INSTALL DECK BOARD ASSEMBLY (for Compact Spare Tire)
Refer to PROCEDURE - Step 44 [10/2015 - 08/2017] , or refer to PROCEDURE - Step 44 [08/2017 - ]
INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
Refer to PROCEDURE - Step 45 [10/2015 - 08/2017] , or refer to PROCEDURE - Step 45 [08/2017 - ]
INSTALL PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY (w/ Partition Net)
Refer to PROCEDURE - Step 46 [10/2015 - 08/2017] , or refer to PROCEDURE - Step 46 [08/2017 - ]