Problem Symptoms Table [12/2012 - 10/2015]
- *: w/ Smart Key System
NOTE:
- Before replacing the certification ECU (smart key ECU assembly), refer to Registration.*
- When replacing the combination meter assembly, make sure to replace it with a new one.
- When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
HINT:
- Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
METER OR GAUGE
| Symptom | Suspected Area | Link |
|---|---|---|
| Speedometer malfunction | Speedometer circuit | Refer to REGISTRATION [12/2012 - ] |
| Tachometer malfunction | Tachometer circuit | Refer to Tachometer Malfunction [12/2012 - ] |
| Fuel receiver gauge malfunction | Fuel receiver gauge circuit | Refer to Fuel Receiver Gauge Malfunction [12/2012 - ] |
WARNING OR INDICATOR
| Symptom | Suspected Area | Link |
|---|---|---|
| Open door warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| Perform Active Test (Indicat. Lamp Doors All Open) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [12/2012 - ] | |
| Brake warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (Indicat. Lamp Brake) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Brake master cylinder reservoir sub-assembly (brake fluid level warning switch) | Refer to DISASSEMBLY [12/2012 - ] | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Front seat belt warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| Perform Active Test (Driver Side Seat Belt) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Seat belt warning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| SRS warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (Indicat. Lamp Airbag) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Airbag system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Engine coolant temperature warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (Indicat. Lamp Coolant Hot) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| ECM | Refer to REMOVAL [12/2012 - ] | |
| Charge warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (Indicat. Lamp Charge) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Harness or connector | - | |
| Generator assembly | Refer to INSPECTION [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| ECM | Refer to REMOVAL [12/2012 - ] | |
| Engine oil pressure warning light does not come on | CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] |
| Perform Active Test (Indicat. Oil Pressure) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Harness or connector | - | |
| Engine oil pressure switch assembly | Refer to INSPECTION [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| A/T OIL TEMP warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (A/T Oil Temperature Operation) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Automatic transaxle system (U760E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Automatic transaxle system (U760F) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| EPS warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (Indicat. EPS) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Power steering system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| MIL does not come on | CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] |
| Harness or connector | - | |
| SFI system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Slip indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (Indicat. Lamp Slip) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| VSC OFF indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (Indicat. VSC OFF) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| TRAC OFF indicator light does not come on (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (VSC TRC Indicator) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| ABS warning light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (Indicat. Lamp ABS) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Tire pressure warning light does not come on (w/ Tire Pressure Warning System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (Indicat. Tire Pressure Warning System) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Tire pressure warning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Fuel level warning light does not come on (Fuel receiver gauge operates normally) | Perform Active Test (Indicat. Lamp Fuel) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| AWD warning light does not come on (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (4WD Warning Indicator) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| AWD lock indicator light does not come on (for AWD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (Indicat. 4WD Lock) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Dynamic torque control AWD system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| AUTO LSD indicator light does not come on (for 2WD) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (Indicat. Auto LSD) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Vehicle stability control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| BSM indicator light does not come on (w/ Blind Spot Monitor System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (Blind Spot Monitor Indicator) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Blind spot monitor sensor | Refer to REMOVAL [12/2012 - 10/2015] | |
| Automatic high beam indicator light does not come on (w/ Automatic High Beam System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (Automatic High Beam Indicator) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [12/2012 - ] | |
| Cruise control indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| Perform Active Test (Indicat. Lamp Cruise, Cruise Indicator) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Smart warning light does not come on (w/ Smart Key System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| Perform Active Test (Smart System Indicator, Smart System Warning) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Certification ECU (smart key ECU assembly) | Refer to REMOVAL [12/2012 - 10/2015] | |
| High beam indicator light does not come on (High beam headlight operates normally) | Harness or connector | - |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [12/2012 - ] | |
| Front fog indicator light does not come on (Front fog light operates normally) (w/ Front Fog Light) | Harness or connector | - |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Turn indicator light does not come on (Turn signal light operates normally) | Perform Active Test [Turn Signal (Left) Indicator, Turn Signal (Right) Indicator] | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| SPORT indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| Perform Active Test [Indicat. Sport (CVT Sport)] | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| ECM | Refer to REMOVAL [12/2012 - ] | |
| ECO MODE indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| Perform Active Test (Indicat. ECO MODE) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| ECM | Refer to REMOVAL [12/2012 - ] | |
| Eco driving indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (Indicat. ECONO) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| ECM | Refer to REMOVAL [12/2012 - ] | |
| SET indicator light does not come on | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| Perform Active Test (Indicat. SET) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Cruise control system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Lane departure alart indicator light does not come on (w/ Lane Departure Alart System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| Perform Active Test [LDA Control Indicator, LDA Warning Indicator, LDA Control Indicator (Left), LDA Warning Indicator (Left), LDA Control Indicator (Right), LDA Warning Indicator (Right)] | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Lane departure warning camera | Refer to REMOVAL [12/2012 - 10/2015] | |
| MAINT REQD indicator light does not come on (for U.S.A.) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| CHeck indicator/warning light | Refer to OPERATION CHECK [12/2012 - 10/2015] | |
| Perform Active Test (Maintenance Indicator) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Brake actuator assembly (skid control ECU) | Refer to REMOVAL [12/2012 - 10/2015] | |
| Washer level indicator light does not come on | Level warning switch assembly | Refer to INSPECTION [12/2012 - ] |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
MULTI-INFORMATION DISPLAY
| Symptom | Suspected Area | Link |
|---|---|---|
| Engine coolant temperature receiver gauge display malfunction | Engine coolant temperature receiver gauge circuit | Refer to Engine Coolant Temperature Receiver Gauge Malfunction [12/2012 - ] |
| Eco driving indicator zone display malfunction | Check customize setting | Refer to CUSTOMIZE PARAMETERS [12/2012 - 10/2015] |
| CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| ECM | Refer to REMOVAL [12/2012 - ] | |
| Outside temperature display malfunction | Thermister assembly | - |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Shift position indicator display malfunction | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| Perform Active Test (A/T Indicator Operation 1, A/T Indicator Operation 2, A/T Indicator Operation 3) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] | |
| Automatic transaxle system (U760E) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Automatic transaxle system (U760F) | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| ECM | Refer to REMOVAL [12/2012 - ] | |
| Current fuel consumption display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
| Average fuel consumption display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
| Cruising range display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
| Average vehicle speed display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
| ODO/TRIP meter display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
| Light control rheostat display malfunction (Combination meter assembly operates normally) | Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
| Multi-information display is missing dots | Perform Active Test (Meter Display 1, Meter Display 2) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Customize setting display malfunction | Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
BUZZER
| Symptom | Suspected Area | Link |
|---|---|---|
| Seat belt warning buzzer does not operate (Seat belt warning light operates normally) | Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
| EPS buzzer does not operate (Power steering system operates normally) | Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
| Smart key system buzzer does not operate (Smart key system operates normally) (w/ Smart Key System) | Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
| Key reminder buzzer does not operate (w/o Smart Key System) | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| Key reminder warning system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [12/2012 - ] | |
| Brake buzzer does not operate (Other systems operate normally) | Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
| Engine immobiliser certification buzzer does not operate (Immobiliser system operates normally) (w/ Smart Key System) | Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
| PKB-ON driving warning buzzer does not operate (Brake warning light operates normally) | Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
| Driving with any door opened warning buzzer does not operate (Other systems operate normally) | Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
| Sports shift reject buzzer does not operate (Other systems operate normally) | Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
| Light reminder buzzer does not operate | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [12/2012 - ] | |
| Turn signal flasher buzzer does not operate (Turn signal light operates normally) | Combination meter assembly | Refer to REMOVAL [12/2012 - ] |
Others
OTHERS
| Symptom | Suspected Area | Link |
|---|---|---|
| Operating light control rheostat does not change light brightness | Light control rheostat | Refer to INSPECTION [12/2012 - ] |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Meter illumination is always dark | CAN communication system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] |
| Lighting system | Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] | |
| Main body ECU (multiplex network body ECU) | Refer to REMOVAL [12/2012 - ] | |
| Multi-information display does not change using DISP switch | Read the Data List (ODO/TRIP Change SW) | Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] |
| Steering pad switch assembly | Refer to INSPECTION [12/2012 - 10/2015] | |
| Spiral cable sub-assembly | Refer to INSPECTION [12/2012 - 10/2015] | |
| Harness or connector | - | |
| Combination meter assembly | Refer to REMOVAL [12/2012 - ] |