Components [12/2012 - 10/2015]: Illustration
| Callout | Description | Callout | Description |
| *1 | THROTTLE WITH MOTOR BODY ASSEMBLY | *2 | NO. 1 WATER BY-PASS HOSE |
| *3 | NO. 2 WATER BY-PASS HOSE | *4 | GASKET |
| *5 | FUEL TUBE BRACKET | - | - |
| Specified torque: N*m (kgf*cm, ft.*lbf) | • | Non-reusable part |
| Callout | Description | Callout | Description |
| *1 | FUEL DELIVERY PIPE | *2 | FUEL TUBE SUB-ASSEMBLY |
| *3 | UNION TO CHECK VALVE HOSE | *4 | VACUUM SWITCHING VALVE ASSEMBLY (for ACIS) |
| *5 | WIRE HARNESS | *6 | NO. 2 FUEL PIPE CLAMP |
| *7 | FUEL DELIVERY SPACER | *8 | INJECTOR VIBRATION INSULATOR |
| *9 | NO. 2 PCV HOSE | - | - |
| Specified torque: N*m (kgf*cm, ft.*lbf) | • | Non-reusable part |
| Callout | Description | Callout | Description |
| *1 | INTAKE MANIFOLD | *2 | NO. 2 PCV HOSE |
| *3 | WIRE HARNESS | *4 | VACUUM SWITCHING VALVE ASSEMBLY (for ACIS) |
| *5 | GASKET | *6 | VACUUM HOSE |
| *7 | WIRING HARNESS CLAMP BRACKET | - | - |
| Specified torque: N*m (kgf*cm, ft.*lbf) | • | Non-reusable part |
| Callout | Description | Callout | Description |
| *1 | EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY | *2 | MANIFOLD STAY |
| *3 | NO. 1 EXHAUST MANIFOLD HEAT INSULATOR | *4 | NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
| *5 | NO. 2 MANIFOLD STAY | *6 | GASKET |
| *7 | RADIATOR HOSE CLAMP | - | - |
| Specified torque: N*m (kgf*cm, ft.*lbf) | • | Non-reusable part |
| Callout | Description | Callout | Description |
| *1 | COOLER COMPRESSOR ASSEMBLY | *2 | ENGINE COOLANT TEMPERATURE SENSOR |
| *3 | ENGINE OIL LEVEL DIPSTICK GUIDE | *4 | ENGINE OIL PRESSURE SWITCH ASSEMBLY |
| *5 | IGNITION COIL ASSEMBLY | *6 | NO. 1 COMPRESSOR MOUNTING BRACKET |
| *7 | ENGINE OIL LEVEL DIPSTICK | *8 | O-RING |
| *9 | GASKET | *10 | NO. 1 WATER BY-PASS HOSE |
| *11 | NO. 2 WATER BY-PASS HOSE | - | - |
| Specified torque: N*m (kgf*cm, ft.*lbf) | • | Non-reusable part | |
| * | Precoated part | - | - |
| Callout | Description | Callout | Description |
| *1 | CAMSHAFT POSITION SENSOR (for Intake Side) | *2 | CAMSHAFT POSITION SENSOR (for Exhaust Side) |
| *3 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side) | *4 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side) |
| *5 | CYLINDER HEAD COVER SUB-ASSEMBLY | *6 | ENGINE COVER JOINT |
| *7 | OIL FILLER CAP SUB-ASSEMBLY | *8 | SPARK PLUG |
| *9 | SPARK PLUG TUBE GASKET | *10 | GASKET |
| *11 | SEAL WASHER | *12 | O-RING |
| *13 | CYLINDER HEAD COVER GASKET | *14 | CAMSHAFT BEARING CAP OIL HOLE GASKET |
| Specified torque: N*m (kgf*cm, ft.*lbf) | • | Non-reusable part | |
| * | Precoated part | - | - |
| Callout | Description | Callout | Description |
| *1 | ENGINE WATER PUMP ASSEMBLY | *2 | NO. 1 WATER BY-PASS PIPE |
| *3 | PCV CASE | *4 | PCV VALVE |
| *5 | SEPARATOR CASE | *6 | THERMOSTAT |
| *7 | V-RIBBED BELT TENSIONER ASSEMBLY | *8 | WATER INLET |
| *9 | WATER INLET HOUSING | *10 | NO. 2 PCV HOSE |
| *11 | GASKET | - | - |
| Specified torque: N*m (kgf*cm, ft.*lbf) | • | Non-reusable part | |
| * | Precoated part | - | - |
| Callout | Description | Callout | Description |
| *1 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY | *2 | CAMSHAFT TIMING GEAR ASSEMBLY |
| *3 | CHAIN SUB-ASSEMBLY | *4 | CHAIN TENSIONER SLIPPER |
| *5 | CRANKSHAFT POSITION SENSOR | *6 | CRANKSHAFT PULLEY |
| *7 | CRANKSHAFT TIMING SPROCKET | *8 | ENGINE MOUNTING BRACKET RH |
| *9 | NO. 1 CHAIN TENSIONER ASSEMBLY | *10 | NO. 1 CHAIN VIBRATION DAMPER |
| *11 | TIMING CHAIN COVER ASSEMBLY | *12 | TIMING CHAIN COVER OIL SEAL |
| *13 | TIMING CHAIN COVER PLATE | *14 | TIMING CHAIN COVER TIGHT PLUG |
| *15 | TIMING CHAIN GUIDE | *16 | GASKET |
| *17 | OIL PUMP GASKET | *18 | OIL HOLE COVER GASKET |
| Specified torque: N*m (kgf*cm, ft.*lbf) | • | Non-reusable part | |
| MP grease | * | Precoated part |
| Callout | Description | Callout | Description |
| *1 | CAMSHAFT HOUSING SUB-ASSEMBLY | *2 | CYLINDER HEAD GASKET |
| *3 | CYLINDER HEAD SUB-ASSEMBLY | *4 | NO. 1 CAMSHAFT BEARING |
| *5 | NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY | *6 | NO. 2 CAMSHAFT BEARING |
| *7 | OIL CONTROL VALVE FILTER | *8 | VALVE LASH ADJUSTER ASSEMBLY |
| *9 | VALVE STEM CAP | *10 | NO. 2 CAMSHAFT BEARING CAP |
| *11 | NO. 1 CAMSHAFT BEARING CAP | *12 | NO. 3 CAMSHAFT BEARING CAP |
| *13 | CAMSHAFT | *14 | NO. 2 CAMSHAFT |
| *15 | PLATE WASHER | - | - |
| Specified torque: N*m (kgf*cm, ft.*lbf) | • | Non-reusable part | |
| *T1 | 1st: 36 (367, 27) 2nd: 36 (367, 27) 3rd: Turn 90° 4th: Turn 90° |
- | - |
| Callout | Description | Callout | Description |
| *1 | CYLINDER BLOCK WATER JACKET SPACER | *2 | ENGINE BALANCER ASSEMBLY |
| *3 | NO. 1 OIL PAN BAFFLE PLATE | *4 | OIL FILTER ELEMENT |
| *5 | OIL PAN SUB-ASSEMBLY | *6 | OIL STRAINER SUB-ASSEMBLY |
| *7 | REAR ENGINE OIL SEAL | *8 | STIFFENING CRANKCASE ASSEMBLY |
| *9 | CYLINDER BLOCK | *10 | O-RING |
| *11 | OIL FILTER CAP ASSEMBLY | *12 | GASKET |
| *13 | OIL PAN DRAIN PLUG | - | - |
| Specified torque: N*m (kgf*cm, ft.*lbf) | • | Non-reusable part | |
| MP grease | * | Precoated part |