Inspection [10/2015 - ]: Procedure
- INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
- Inspect the light control switch.
*a Component without harness connected
(Headlight Dimmer Switch Assembly)- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Switch Condition Specified Condition G13-20 (A) - G13-15 (EL) Light control switch off*A
or
Light control switch DRL off*B10 kΩ or higher G13-19 (H) - G13-15 (EL) G13-18 (T) - G13-15 (EL) G13-20 (A) - G13-15 (EL) Light control switch DRL*A position
or
Light control switch AUTO*B positionBelow 1 Ω G13-18 (T) - G13-15 (EL) Light control switch tail position Below 1 Ω G13-18 (T) - G13-15 (EL) Light control switch head position Below 1 Ω G13-19 (H) - G13-15 (EL) *A: w/o Automatic Light Control System
*B: w/ Automatic Light Control System
If the result is not as specified, replace the headlight dimmer switch assembly.
- Measure the resistance according to the value(s) in the table below.
- Inspect the headlight dimmer switch.
*a Component without harness connected
(Headlight Dimmer Switch Assembly)- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Switch Condition Specified Condition G13-14 (HU) - G13-15 (EL) Headlight dimmer switch flash position Below 1 Ω G13-17 (HF) - G13-15 (EL) G13-14 (HU) - G13-15 (EL) Headlight dimmer switch high position Below 1 Ω If the result is not as specified, replace the headlight dimmer switch assembly.
- Measure the resistance according to the value(s) in the table below.
- Inspect the turn signal light switch.
*a Component without harness connected
(Headlight Dimmer Switch Assembly)- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Switch Condition Specified Condition G13-12(TR) - G13-15(EL) Turn signal switch neutral position 10 kΩ or higher G13-11(TL) - G13-15(EL) G13-13(CR) - G13-15(EL) G13-12(TR) - G13-15(EL) Turn signal switch right turn position
(self cancel condition)Below 1 Ω G13-12(TR) - G13-15(EL) Turn signal switch right turn position
(cancel ratchet operation condition)Below 1 Ω G13-12(TR) - G13-13(CR) G13-13(CR) - G13-15(EL) G13-11(TL) - G13-15(EL) Turn signal switch left turn position
(self cancel condition)Below 1 Ω G13-11(TL) - G13-15(EL) Turn signal switch left turn position
(cancel ratchet operation condition)Below 1 Ω G13-11(TL) - G13-13(CR) G13-13(CR) - G13-15(EL) HINT:
- The self cancel condition indicates when the turn signal switch returns to the neutral position after releasing your hand from the switch (switch is operated within 7°).
- The cancel ratchet operation condition indicates the condition when the turn signal switch does not return to the neutral position even after releasing your hand (switch operation is 12°).
If the result is not as specified, replace the headlight dimmer switch assembly.
- Measure the resistance according to the value(s) in the table below.
*a Component without harness connected
(Headlight Dimmer Switch Assembly)Inspect the fog light switch.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Switch Condition Specified Condition G13-9 (BFG) - G13-8 (LFG) Front fog light switch off 10 kΩ or higher G13-9 (BFG) - G13-8 (LFG) Front fog light switch on Below 1 Ω If the result is not as specified, replace the headlight dimmer switch assembly.
- Measure the resistance according to the value(s) in the table below.
- Inspect the light control switch.