LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2018 >> Prius Two Eco >> Repair and Diagnosis >> Body & Frame >> Exterior/Interior Trim >> Interior Panels / Trim - Service Information (2 Of 2) >> Roof Headlining >> Removal [11/2015 - 12/2018] >> Procedure

Removal [11/2015 - 12/2018]: Procedure

  1. REMOVE TONNEAU COVER ASSEMBLY 
    1. Remove the tonneau cover assembly.
  2. REMOVE REAR NO. 1 FLOOR BOARD 
    1. Remove the rear No. 1 floor board.
  3. REMOVE DECK BOARD RETAINER 
    1. for LH Side:
      GTY596136Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
      1. Disengage the clip and guide to remove the deck board retainer as shown in the illustration.
    2. for RH Side:
      GTY555209Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
      1. Disengage the clip and guide to remove the deck board retainer as shown in the illustration.
  4. REMOVE DECK FLOOR BOX LH (w/o Spare Tire) 
    1. Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box LH as shown in the illustration, turn the clip to remove the deck floor box LH.
      GTY550310Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      Turn in this Direction
      Remove in this Direction
  5. REMOVE DECK FLOOR BOX RH (w/o Spare Tire) 
    1. Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box RH as shown in the illustration, turn the clip to remove the deck floor box RH.
      GTY564795Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      Turn in this Direction
      Remove in this Direction
  6. REMOVE REAR DECK FLOOR BOX (w/ Compact Spare Tire) 
    1. Remove the rear deck floor box.
  7. REMOVE DECK FLOOR BOX LH (w/ Compact Spare Tire) 
    1. Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box LH as shown in the illustration, turn the clip to remove the deck floor box LH.
      GTY577559Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      Turn in this Direction
      Remove in this Direction
  8. REMOVE DECK FLOOR BOX RH (w/ Compact Spare Tire) 
    1. Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box RH as shown in the illustration, turn the clip to remove the deck floor box RH.
      GTY604639Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      Turn in this Direction
      Remove in this Direction
  9. REMOVE DECK FLOOR BOX RH (w/ Full Size Spare Tire) 
    1. Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box RH as shown in the illustration, turn the clip to remove the deck floor box RH.
      GTY588006Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      Turn in this Direction
      Remove in this Direction
  10. REMOVE DECK FLOOR BOX LH (w/ Full Size Spare Tire) 
    1. Using a screwdriver with its tip wrapped with protective tape, while pulling the deck floor box LH as shown in the illustration, turn the clip to remove the deck floor box LH.
      GTY555333Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      Turn in this Direction
      Remove in this Direction
  11. REMOVE DECK TRIM SERVICE HOLE COVER 

    Refer to PROCEDURE - Step 2

  12. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for Rear Side) 
    1. Remove the 2 bolts.
      GTY566572Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 2 guides to remove the 2 luggage hold belt striker assemblies.
  13. REMOVE REAR DECK TRIM COVER 
    1. Disengage the 4 clips and 2 guides to remove the rear deck trim cover as shown in the illustration.
      GTY609808Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  14. REMOVE FRONT DOOR SCUFF PLATE LH 
    1. Disengage the claw as shown in the illustration.
      GTY600989Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction

      HINT: 

      Use the same procedure for the front side and rear side.

    2. Disengage the 6 claws and 2 guides to remove the front door scuff plate LH as shown in the illustration.
      GTY581862Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  15. REMOVE COWL SIDE TRIM BOARD LH 
    1. Remove the clip.
      GTY604947Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    2. Disengage the 2 clips to remove the cowl side trim board LH as shown in the illustration.
  16. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 3

  17. REMOVE FRONT PILLAR GARNISH LH 
    1. Apply protective tape around the front pillar garnish LH as shown in the illustration.
      GTY586028Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Protective Tape
    2. Pull the upper part of the front pillar garnish LH toward the inside of the cabin to disengage the clip and the front pillar garnish LH from the base of the front pillar garnish clip.

      HINT: 

      Let the front pillar garnish LH hang from the front pillar garnish clip.

      GTY539722Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Pillar Garnish Clip
      Place Hand Here
      Remove in this Direction
    3. While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.
      GTY596053Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Pillar Garnish Clip
      Remove in this Direction
      NOTE:

      The front pillar garnish clip is reusable if it is not damaged.

    4. When the front pillar garnish clip cannot be removed using your fingers:
      1. While pressing the part shown in the illustration with your finger, move the front pillar garnish clip in the direction indicated by the arrow (1) shown in the illustration.
        GTY570751Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Lift in this Direction (1)
      2. While pulling the front pillar garnish clip in the direction indicated by the arrow (2), push the part shown in the illustration with the end of a screwdriver and remove the front pillar garnish clip.
        NOTE:

        If the front pillar garnish clip is damaged, replace it with a new one.

        GTY585027Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Pull in this Direction (2)
    5. Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.
      GTY556323Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    6. Protect the curtain shield airbag assembly LH.
      GTY561192Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Curtain Shield Airbag Assembly LH
      *a Protective Cover
      *b Adhesive Tape
      1. Cover the curtain shield airbag assembly LH with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.
        NOTE:

        Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.

  18. REMOVE REAR DOOR SCUFF PLATE LH 
    1. Disengage the claw as shown in the illustration.
      GTY607184Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    2. Disengage the 6 claws and 3 guides to remove the rear door scuff plate LH as shown in the illustration.
      GTY541514Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  19. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 2

  20. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side) 

    Refer to PROCEDURE - Step 7

  21. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH 

    Refer to PROCEDURE - Step 8

  22. REMOVE LOWER CENTER PILLAR GARNISH LH 
    1. Pull the lower center pillar garnish LH in the directions indicated by the arrows (1) shown in the illustration to disengage the 2 claws (A).
      GTY601098Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Claw (A)
      *b Claw (B)
      Place Hand Here
      Remove in this Direction (1)
      Remove in this Direction (2)
    2. Pull the lower center pillar garnish LH in the direction indicated by the arrow (2) shown in the illustration to disengage the 2 claws (B).
    3. Disengage the 3 clips to remove the lower center pillar garnish LH as shown in the illustration.
      GTY591539Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
  23. REMOVE CENTER PILLAR GARNISH ASSEMBLY LH 
    1. Using a clip remover, remove the 2 clips.
      GTY603763Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the guide as shown in the illustration.
      GTY586466Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    3. Disengage the clip and 2 guides to remove the center pillar garnish assembly LH as shown in the illustration.
      GTY606989Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
  24. REMOVE FRONT DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedure as for the LH side.

  25. REMOVE COWL SIDE TRIM BOARD RH 

    HINT: 

    Use the same procedure as for the LH side.

  26. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH 

    HINT: 

    Use the same procedure as for the LH side.

  27. REMOVE FRONT PILLAR GARNISH RH 

    HINT: 

    Use the same procedure as for the LH side.

  28. REMOVE REAR DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedure as for the LH side.

  29. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH 

    HINT: 

    Use the same procedure as for the LH side.

  30. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side) 

    HINT: 

    Use the same procedure as for the LH side.

  31. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  32. REMOVE LOWER CENTER PILLAR GARNISH RH 

    HINT: 

    Use the same procedure as for the LH side.

  33. REMOVE CENTER PILLAR GARNISH ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  34. REMOVE REAR SEAT ASSEMBLY 

    Refer to REMOVAL [11/2015 -]

  35. REMOVE REAR UNDER SIDE COVER LH 
    1. Remove the 2 clips.
      GTY573661Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    2. Disengage the claw, 4 clips and guide to remove the rear under side cover LH as shown in the illustration.
  36. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH 
    1. Loosen the bolt to remove the rear seatback hinge sub-assembly LH.
      GTY566687Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  37. REMOVE REAR SEAT SIDE GARNISH LH 
    1. Disengage the claw as shown in the illustration.
      GTY591119Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    2. Disengage the 2 clips and 2 guides to remove the rear seat side garnish LH as shown in the illustration.
      GTY602021Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  38. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side) 
    1. Remove the bolt.
      GTY566674Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the guide to remove the luggage hold belt striker assembly.
  39. REMOVE ROPE HOOK (for LH Side without Blind Spot Monitor System) 
    1. Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and remove the rope hook as shown in the illustration.
      GTY564910Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      Insert Screwdriver Here
      Remove in this Direction
  40. REMOVE NO. 2 ROPE HOOK (for LH Side without Blind Spot Monitor System) 
    1. Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the No. 2 rope hook as shown in the illustration.
      GTY569610Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      Insert Screwdriver Here
      Remove in this Direction
  41. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (for LH Side with Blind Spot Monitor System) 
    1. Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the No. 1 tonneau cover holder cap as shown in the illustration.
      GTY548151Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      Insert Screwdriver Here
      Remove in this Direction
  42. REMOVE TONNEAU COVER HOOK A (for LH Side with Blind Spot Monitor System) 
    1. Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the tonneau cover hook A as shown in the illustration.
      GTY561730Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      Insert Screwdriver Here
      Remove in this Direction
  43. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 1

  44. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH 
    1. Lower the No. 2 luggage compartment trim hook as shown in the illustration.
      GTY574325Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 No. 2 Luggage Compartment Trim Hook
    2. Using a screwdriver with its tip wrapped with protective tape, disengage the clip as shown in the illustration.
      GTY569633Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 No. 2 Luggage Compartment Trim Hook
      *a Protective Tape
      *b Hole (A)
      *c Clip
      Insert Screwdriver Here
      Remove in this Direction

      HINT: 

      Insert the screwdriver into the hole (A).

    3. Remove the 2 screws.
      GTY552696Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Disengage the 5 claws, 2 clips and guide to remove the deck trim side panel assembly LH as shown in the illustration.
      GTY605442Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
  45. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH 
    1. Disengage the 5 clips as shown in the illustration to remove the roof side inner garnish assembly LH.
      GTY593460Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
  46. REMOVE REAR UNDER SIDE COVER RH 

    HINT: 

    Use the same procedure as for the LH side.

  47. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  48. REMOVE REAR SEAT SIDE GARNISH RH 

    HINT: 

    Use the same procedure as for the LH side.

  49. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side) 

    HINT: 

    Use the same procedure as for the LH side.

  50. REMOVE ROPE HOOK (for RH Side without Blind Spot Monitor System) 

    HINT: 

    Use the same procedure as for the LH side.

  51. REMOVE NO. 2 ROPE HOOK (for RH Side without Blind Spot Monitor System) 

    HINT: 

    Use the same procedure as for the LH side.

  52. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (for RH Side with Blind Spot Monitor System) 

    HINT: 

    Use the same procedure as for the LH side.

  53. REMOVE TONNEAU COVER HOOK A (for RH Side with Blind Spot Monitor System) 

    HINT: 

    Use the same procedure as for the LH side.

  54. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  55. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  56. REMOVE ROOF CONSOLE BOX ASSEMBLY 

    Refer to PROCEDURE - Step 1

  57. REMOVE NO. 1 ROOM LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 1

  58. REMOVE SENSOR COVER (w/ Humidity Sensor) 

    Refer to PROCEDURE - Step 1

  59. REMOVE AIR CONDITIONING THERMISTOR ASSEMBLY (w/ Humidity Sensor) 

    Refer to PROCEDURE - Step 3

  60. REMOVE RAIN SENSOR COVER (w/ Rain Sensor) 

    Refer to PROCEDURE - Step 1

  61. REMOVE RAIN SENSOR (w/ Rain Sensor) 

    Refer to PROCEDURE - Step 2

  62. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ Inner Rear View Mirror Stay Holder Cover) 

    Refer to PROCEDURE - Step 1

  63. REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Toyota Safety Sense P) 

    Refer to PROCEDURE - Step 1

  64. REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Toyota Safety Sense P) 

    Refer to PROCEDURE - Step 2

  65. REMOVE ASSIST GRIP ASSEMBLY 

    HINT: 

    Use the same procedure for all assist grip assemblies.

    1. Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and remove the assist grip cover LH.
      GTY598987Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      Insert Screwdriver Here

      HINT: 

      Use the same procedure for the RH side and LH side.

    2. Disengage the 2 clips as shown in the illustration to remove the assist grip assembly.
      GTY561348Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    3. Remove the 2 clips from the vehicle body.
  66. REMOVE REAR ASSIST GRIP ASSEMBLY LH 

    HINT: 

    Use the same procedure as for the assist grip assembly.

  67. REMOVE REAR ASSIST GRIP ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the assist grip assembly.

  68. REMOVE VISOR BRACKET COVER (for LH Side) 
    1. Using a moulding remover, disengage the 4 claws as shown in the illustration and remove the visor bracket cover.
      GTY578687Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Insert Moulding Remover Here
  69. REMOVE VISOR ASSEMBLY LH 
    1. Remove the 2 screws.
      GTY552554Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Pull the visor assembly LH in the direction indicated by the arrow (1) shown in the illustration to disconnect it from the visor holder.
      GTY603553Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Visor Holder
      Remove in this Direction (1)
      Remove in this Direction (2)
    3. Pull the visor assembly LH in the direction indicated by the arrow (2) shown in the illustration to remove it.
  70. REMOVE VISOR HOLDER LH 
    1. Turn the visor holder approximately 45° and pull it out as indicated by the arrows, in the order shown in the illustration.
      GTY602037Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a 45°
      Remove in this Direction (1)
      Remove in this Direction (2)
    2. Disengage the 2 claws to remove the visor holder.
  71. REMOVE VISOR BRACKET COVER (for RH Side) 

    HINT: 

    Use the same procedure as for the LH side.

  72. REMOVE VISOR ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  73. REMOVE VISOR HOLDER RH 

    HINT: 

    Use the same procedure as for the LH side.

  74. REMOVE ROOF HEADLINING ASSEMBLY 
    1. for Windshield Glass Side:
      1. Disconnect each connector.
    2. for Front Pillar LH Side:
      1. Remove the protective cover.
      2. Using a clip remover, disengage the 4 clamps.
        GTY552376Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Disconnect the 2 connectors.
      4. Install the protective cover.
    3. for Front Pillar RH Side:
      1. Remove the protective cover.
      2. Using a clip remover, disengage the 3 clamps.
        GTY552379Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Disconnect each connector.
      4. Install the protective cover.
    4. for Rear Pillar RH Side:
      GTY552525Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Disconnect the 2 connectors.
    5. for Roof Side (w/o Sliding Roof):
      GTY552522Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Using a clip remover, remove the 3 clips.
    6. for Roof Side (w/ Sliding Roof):
      GTY606664Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Fastener *b Guide
      *c Clamp - -
      1. Using a clip remover, disengage the clamp.
      2. Disconnect the connector.
      3. Using a clip remover, remove the 3 clips.
      4. Disengage the 6 fasteners and guide.
    7. Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.
      NOTE:

      Do not damage the roof headlining assembly or vehicle interior.

      GTY590091Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
scientia non olet · About LEMON Manuals