DTC P3000-00: Hybrid/EV Battery Discharge Control Malfunction [11/2015 - ]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
4. Check for DTCs.

   Powertrain > Hybrid Control > Trouble Codes 

   Result

   Result	Proceed to
   Only P3000-00 is output	A
   Only P3000-16 is output	B
   Other than above	C

5. Turn the power switch off.

Result: 

B 

See step  2

Result: 

C 

GO TO DTC CHART (HYBRID CONTROL SYSTEM). Refer to  DIAGNOSTIC TROUBLE CODE CHART [11/2015 - 11/2017]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [11/2017 - 12/2018]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [12/2018 - 08/2019]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2019 - 06/2021]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [06/2021 - ] 

Result: 

A 

See step  2

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Enter the following menus: Powertrain / Engine / Trouble Codes.
4. Check for DTCs.

   Powertrain > Engine > Trouble Codes 

   Result

   Result	Proceed to
   DTCs are not output	A
   DTCs are output	B

5. Turn the power switch off.

Result: 

B 

GO TO DTC CHART (SFI SYSTEM). Refer to  DIAGNOSTIC TROUBLE CODE CHART [11/2015 - 08/2016]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2016 - 11/2017]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [11/2017 - 12/2018]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [12/2018 - 08/2019]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2019 - 07/2020]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [07/2020 - ] 

Result: 

A 

See step  3

1. Turn the power switch on (IG).
2. Check the amount of fuel by referring to the fuel gauge in the meter.

   Result

   Result	Proceed to
   Proper amount of fuel is in the tank.	A
   There is no fuel in the tank.	B

   HINT: 

   Add fuel until the low fuel level warning light turns off.

3. Turn the power switch off.

Result: 

B 

REFUEL VEHICLE 

Result: 

A 

See step  4

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Read the freeze frame data item "Shift Position" of DTC P3000-00.

   Powertrain > Hybrid Control > DTC(P3000-00) > Freeze Frame Data 

   Tester Display
   Shift Position

   NOTE:

   • When the freeze frame data "Shift Position" was N, DTC P3000-00 may be stored due to the vehicle was left with neutral (N) selected and the HV battery could not be charged.
   • If DTC "P3000-00" only is output, charge the HV battery without replacing the HV battery if necessary.
4. Turn the power switch off.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  5

1. Turn the power switch on (READY).
2. Check if the engine starts.

   HINT: 

   • Depressing the accelerator pedal with park (P) selected will cause the engine to start.
   • Turning the power switch on (READY) and off repeatedly while the SOC is low may cause the SOC to drop further, resulting in DTC P3000-16 being stored. Charge the HV battery using the THS charger as necessary.
   • Cranking the engine once causes the SOC to drop approximately 1%.
   • Charging the HV battery once (10 minutes) using the THS charger restores the SOC approximately 2%.

   Result

   Result	Proceed to
   The engine starts	A
   The engine does not start	B

3. If the engine does not start, turn the power switch off.

Result: 

A 

LEAVE VEHICLE WITH PARK (P) SELECTED, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS 

Result: 

B 

See step  6

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
4. Clear the DTCs.

   Powertrain > Hybrid Control > Clear DTCs 

5. Turn the power switch off and wait for 2 minutes or more.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

CHARGE HV BATTERY (CHECK THAT ENGINE STARTS). Refer to  CHARGING [11/2015 - 11/2017]  , or refer to  CHARGING [11/2017 - 12/2018]  , or refer to  CHARGING [12/2018 - 07/2020]  , or refer to  CHARGING [07/2020 - ]