LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2018 >> Prius One >> Repair and Diagnosis >> External Pages >> Different car >> Section 211 (Engine Control System (Service Information) [2GR-FKS]) >> Air Fuel Ratio Sensor >> Installation [04/2018 - ] >> Procedure

Installation [04/2018 - ]: Procedure

WARNING: This page is about a different car, the 2022 Toyota Avalon, 2021 Toyota Avalon, 2020 Toyota Avalon, and 2019 Toyota Avalon. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL AIR FUEL RATIO SENSOR (for Bank 1) 

    HINT: 

    Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

    Refer to INITIALIZATION [04/2018 - 08/2019] , or refer to INITIALIZATION [08/2019 - ]

    1. Using SST, install the air fuel ratio sensor to the exhaust manifold assembly RH (TWC: Front Catalyst).
      GTY761663Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Torque Wrench Fulcrum Length
      • SST: 09224-00012 

      Specified tightening torque 

      Torque: 44 N*m (449 kgf*cm, 32 ft.*lbf) 

      NOTE:

      If the air fuel ratio sensor has been struck or dropped, replace it.

      HINT: 

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Refer to PRECAUTION [04/2018 - ]

      • When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

        37.7 N*m (384 kgf*cm, 28 ft.*lbf)

    2. Engage the 2 wire harness clamps.
    3. Connect the air fuel ratio sensor connector.
  2. INSTALL AIR FUEL RATIO SENSOR (for Bank 2) 

    HINT: 

    Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

    Refer to INITIALIZATION [04/2018 - 08/2019] , or refer to INITIALIZATION [08/2019 - ]

    1. Using SST, install the air fuel ratio sensor to the exhaust manifold assembly LH (TWC: Front Catalyst).
      GTY760350Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Torque Wrench Fulcrum Length
      • SST: 09224-00012 

      Specified tightening torque 

      Torque: 44 N*m (449 kgf*cm, 32 ft.*lbf) 

      NOTE:

      If the air fuel ratio sensor has been struck or dropped, replace it.

      HINT: 

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Refer to PRECAUTION [04/2018 - ]

      • When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

        37.7 N*m (384 kgf*cm, 28 ft.*lbf)

    2. Connect the air fuel ratio sensor connector.
    3. Engage the wire harness clamp.
  3. INSTALL V-BANK COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 46

  4. INSPECT FOR EXHAUST GAS LEAK 

    Refer to PROCEDURE - Step 14

  5. PERFORM INITIALIZATION 
    1. Perform "Inspection After Repair" after replacing an air fuel ratio sensor.

      Refer to INITIALIZATION [04/2018 - 08/2019] , or refer to INITIALIZATION [08/2019 - ]