LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2018 >> Highlander XLE, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 109 (Engine Control System (2GR-FXS) - Service Information - (Hybrid)) >> Heated Oxygen Sensor >> Installation [11/2016 - ] >> Procedure

Installation [11/2016 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. INSTALL HEATED OXYGEN SENSOR (for Bank 2) 

    HINT: 

    Perform "Inspection After Repair" after replacing the heated oxygen sensor.

    Refer to INITIALIZATION [11/2016 - ]

    1. Using SST, install the heated oxygen sensor to the front exhaust pipe assembly.
      GTY713170Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Torque Wrench Fulcrum Length
      • SST: 09224-00012 

      Specified tightening torque 

      Torque: 44 N*m (449 kgf*cm, 32 ft.*lbf) 

      NOTE:

      If the heated oxygen sensor has been struck or dropped, replace it.

      HINT: 

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Refer to PRECAUTION [11/2016 - ]

      • When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

        37.7 N*m (384 kgf*cm, 28 ft.*lbf)

  2. INSTALL FRONT EXHAUST PIPE ASSEMBLY 

    Refer to PROCEDURE - Step 7

  3. INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 19

  4. INSTALL NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 84

  5. INSTALL HEATED OXYGEN SENSOR (for Bank 1) 

    HINT: 

    Perform "Inspection After Repair" after replacing the heated oxygen sensor.

    Refer to INITIALIZATION [11/2016 - ]

    1. Using SST, install the heated oxygen sensor to the front No. 3 exhaust pipe sub-assembly.
      GTY729768Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Torque Wrench Fulcrum Length
      • SST: 09224-00012 

      Specified tightening torque 

      Torque: 44 N*m (449 kgf*cm, 32 ft.*lbf) 

      NOTE:

      If the heated oxygen sensor has been struck or dropped, replace it.

      HINT: 

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Refer to PRECAUTION [11/2016 - ]

      • When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

        37.7 N*m (384 kgf*cm, 28 ft.*lbf)

    2. Engage the 3 wire harness clamps.
    3. Connect the heated oxygen sensor connector.
  6. INSPECT FOR EXHAUST GAS LEAK 

    Refer to PROCEDURE - Step 10

  7. INSTALL NO. 2 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 83

  8. INSTALL FRONT FLOOR COVER LH 

    Refer to PROCEDURE - Step 26

  9. PERFORM INITIALIZATION 
    1. Perform "Inspection After Repair" after replacing the heated oxygen sensor.

      Refer to INITIALIZATION [11/2016 - ]

scientia non olet · About LEMON Manuals