LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2018 >> Highlander XLE, AWD >> Repair and Diagnosis >> Engine Performance >> Testing & Diagnosis >> SFI System [2GR-FKS] - Diagnostic Codes - (Except Hybrid) (3 Of 4) >> SFI System >> DTC P0443-13: Evaporative Emission System Purge Control Valve "A" Circuit Open [11/2016 - ] >> Procedure

DTC P0443-13: Evaporative Emission System Purge Control Valve "A" Circuit Open [11/2016 - ]: Procedure

  1. PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE EVAP PURGE VSV) 
    GTY687374Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a VSV is on
    *b VSV is off
    1. Connect the Techstream to the DLC3.
    2. Disconnect the fuel vapor feed hose (on the canister side) from the purge VSV.
    3. Turn the ignition switch to ON.
    4. Turn the Techstream on.
    5. Start the engine.
    6. Enter the following menus: Powertrain / Engine / Active Test / Activate the EVAP Purge VSV.

      Powertrain > Engine > Active Test 

      Tester Display
      Activate the EVAP Purge VSV
    7. When the purge VSV is operated using the Techstream, check whether the port of the purge VSV applies suction to your finger.

      OK

      Techstream Operation Specified Condition
      ON Purge VSV port applies suction to finger
      OFF Purge VSV port applies no suction to finger

      HINT: 

      Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

      Proceed to
      OK
      NG

    Result: 

    OK 

    CHECK FOR INTERMITTENT PROBLEMS. Refer to  CHECK FOR INTERMITTENT PROBLEMS [11/2016 - ] 

    Result: 

    NG 

    Go to next step 

  2. INSPECT PURGE VSV 
    1. Inspect the purge VSV.

      Refer to INSPECTION [11/2016 - ]

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE PURGE VSV. Refer to  REMOVAL [11/2016 - ] 

    Result: 

    OK 

    Go to next step 

  3. CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV) 
    GTY699977Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Front view of wire harness connector
    (to Purge VSV)
    1. Disconnect the purge VSV connector.
    2. Turn the ignition switch to ON.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      C11-1 - Body ground Ignition switch ON 11 to 14 V
      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  5

    Result: 

    OK 

    Go to next step 

  4. CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM) 
    1. Disconnect the purge VSV connector.
    2. Disconnect the ECM connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C11-2 - C1-65 (PRG) Always Below 1 Ω
      C11-2 or C1-65 (PRG) - Body ground and other terminals Always 10 kΩ or higher
      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ECM. Refer to  REMOVAL [11/2016 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  5. CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - PURGE VSV) 
    1. Disconnect the semiconductor pwr integration ECU connector.
    2. Disconnect the purge VSV connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      1G-7 - C11-1 Always Below 1 Ω
      1G-7 or C11-1 - Body ground and other terminals Always 10 kΩ or higher
      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE SEMICONDUCTOR POWER INTEGRATION ECU. Refer to  REMOVAL [12/2013 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals