LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2018 >> Highlander LE Plus, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 111 (SFI System (2GR-FXS) - Diagnostic Codes - (Hybrid) (3 Of 4)) >> SFI System >> DTC P0106: Manifold Absolute Pressure Circuit Problem [11/2016 - ] >> Procedure

DTC P0106: Manifold Absolute Pressure Circuit Problem [11/2016 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0106) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
    5. Read the DTCs.

      Powertrain > Engine and ECT > Trouble Codes 

      Result

      Result Proceed to
      DTC P0106 is output A
      DTC P0106 and other DTCs are output B

      HINT: 

      If any DTCs other than P0106 are output, troubleshoot those DTCs first.

    Result: 

    B 

    GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [11/2016 - 10/2017]  or  DIAGNOSTIC TROUBLE CODE CHART [10/2017 - ] 

    Result: 

    A 

    See step  2

  2. READ VALUE USING TECHSTREAM (MAP) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Throttle Idle Position.

      Powertrain > Engine and ECT > Data List 

      Tester Display
      MAP
      Throttle Idle Position
    5. Read the MAP value.
    6. Put the engine in inspection mode (maintenance mode).

      Powertrain > Hybrid Control > Utility 

      Tester Display
      Inspection Mode
    7. Start the engine.
    8. Confirm that the value of Data List item Throttle Idle Position is "ON" then check the value of MAP.
      Engine Condition Techstream Display
      Throttle Idle Position MAP
      Power switch on (IG) (Engine stopped) - 80 to 110 kPa (11.6 to 15.95 psi)
      Idling (Not Charge Control) ON 20 to 40 kPa (2.9 to 5.8 psi)

      HINT: 

      If the value of Data List item Throttle Idle Position is "OFF" when the engine is idling, charge control is being performed. Check the Intake MAP after charge control is complete ("ON" is displayed).

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    CHECK FOR INTERMITTENT PROBLEMS. Refer to  CHECK FOR INTERMITTENT PROBLEMS [11/2016 - ] 

    Result: 

    NG 

    See step  3

  3. CHECK INTAKE SYSTEM 
    1. Check the intake system for vacuum leaks.

      Refer to ON-VEHICLE INSPECTION [11/2016 - ]

      OK

      No leaks in intake system.

      HINT: 

      Perform "Inspection After Repair" after repairing or replacing the intake system.

      Refer to INITIALIZATION [11/2016 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR. Refer to  REMOVAL [11/2016 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE INTAKE SYSTEM 

scientia non olet · About LEMON Manuals