LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2018 >> Camry LE >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 29 (Fuel System (2GR-FKS) - Service Information (Except Hybrid)) >> FUEL INJECTOR (for Port Injection) >> Inspection [06/2017 - ] >> Procedure

Inspection [06/2017 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. INSPECT FUEL INJECTOR ASSEMBLY 
    1. Check the resistance.
      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        1 - 2 20°C (68°F) 11.6 to 12.4 Ω

        If the result is not as specified, replace the fuel injector assembly.

        GTY517763Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Fuel Injector Assembly)
    2. Check the operation.
      WARNING:

      Perform the inspection in a well-ventilated area.

      Do not perform the inspection near an open flame.

      1. Disengage the 2 claws to remove the No. 2 fuel pipe clamp.
        GTY773653Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Remove the No. 1 fuel pipe clamp from the fuel tube connector.
        GTY739823Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Disconnect the fuel tube sub-assembly.

        Refer to PRECAUTION [06/2017 - 09/2019] , or refer to PRECAUTION [09/2019 - ]

        GTY763754Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      4. Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel pipe (vehicle side).
        GTY453609Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a SST (Hose)
        *b SST (Hose Band)
        *c SST (Fuel Tube Connector)
        *d Fuel Pipe (Vehicle Side)
        • SST: 09268-31015 
          1. 09268-41500
          2. 09268-41700
          3. 95336-08070
        NOTE:

        Make sure the SST (fuel tube connector) O-rings are not damaged and are free of foreign matter as they are used to seal the connections between the fuel tube connector and fuel pipe.

      5. Apply a light coat of gasoline to a new O-ring, and then install the O-ring to the fuel injector assembly.
      6. Connect SST (adapter) and SST (hose) to the fuel injector assembly, and hold the fuel injector assembly and union with SST (clamp).
        GTY677103Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *1 O-ring
        *a SST (Adapter)
        *b SST (Hose Band)
        *c SST (Clamp)
        *d SST (Hose)
        *e Vinyl Tube
        • SST: 09268-31015 
          1. 09268-41600
          2. 09268-41300
          3. 09268-41700
          4. 95336-08070
      7. Tie SST (clamp) and SST (adapter) together with SST (tie band) as shown in the illustration.
        GTY501282Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Lock
        *b SST (Tie Band)
        • SST: 09268-31015 
          1. 09268-41800
        NOTE:
        • As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.
        • Before using SST (tie band), make sure that there is no wear, damage or cracks. If there are any abnormalities, replace SST.

        HINT: 

        When removing SST (tie band), disengage the lock.

      8. Check that SST (clamp) and SST (adapter) cannot be easily separated.
      9. Install a vinyl tube to the fuel injector assembly.
        WARNING:

        Install a suitable vinyl tube to the fuel injector assembly to prevent fuel from spraying.

      10. Set the fuel injector assembly into a graduated cylinder.
      11. Connect the Techstream to the DLC3.
      12. Turn the engine switch on (IG).
        NOTE:

        Do not start the engine.

      13. Turn the Techstream on.
      14. Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

        Powertrain > Engine > Active Test 

        Tester Display
        Activate the Circuit Relay
      15. Connect SST (EFI inspection wire I) to the fuel injector assembly and battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each fuel injector assembly 2 or 3 times.
        GTY508352Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a SST (EFI Inspection Wire I)
        • SST: 09842-30090 

        Standard Injection Volume

        Tester Connection Condition Specified Condition
        Positive (+) battery terminal - Negative (-) battery terminal Per 15 seconds 67 to 81 cc (4.1 to 4.9 cu. in.)

        Difference between Each Fuel Injector Assembly

        14 cc (0.9 cu. in.) or less

        NOTE:
        • Make sure that SST (EFI inspection wire I) is securely connected.
        • Always switch the voltage on and off at the battery side, not the fuel injector assembly side.

        If the injection volume is not as specified, replace the fuel injector assembly.

    3. Check for leaks.
      1. Disconnect SST (EFI inspection wire I) from the battery and check for fuel leaks from the fuel injector assembly.

        Standard Fuel Drop

        1 drop or less per 20 minutes

        If the result is not as specified, replace the fuel injector assembly.

      2. Connect the fuel tube sub-assembly.

        Refer to PRECAUTION [06/2017 - 09/2019] , or refer to PRECAUTION [09/2019 - ]

      3. Install the No. 1 fuel pipe clamp to the fuel tube connector.
      4. Engage the 2 claws to install the No. 2 fuel pipe clamp.
      5. Check for fuel leaks.

        Refer to PROCEDURE - Step 1

scientia non olet · About LEMON Manuals