How To Proceed With Troubleshooting [10/2020 - ]: Procedure

Result

Result: 

NEXT 

See step  2

Result

Result: 

NEXT 

See step  3

1. Measure the battery voltage.

   Standard Voltage

   11 to 14 V

   If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  4

1. Use the GTS to check if the CAN communication system is functioning normally.
   1. Refer to DIAGNOSIS SYSTEM [10/2020 - 08/2021] , or refer to DIAGNOSIS SYSTEM [08/2021 - ]

   Result

   Result	Proceed to
   CAN communication system DTCs are not output	A
   CAN communication system DTCs are output	B

Result: 

B 

GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [03/2017 - ] 

Result: 

A 

See step  5

1. Use the GTS to check if the blind spot monitor system is functioning normally.

   Refer to DTC CHECK / CLEAR [06/2017 - ]

   Result

   Result	Proceed to
   DTCs are not output	A
   DTCs are output	B

Result: 

B 

GO TO BLIND SPOT MONITOR SENSOR. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [03/2017 - ] 

Result: 

A 

See step  6

Result

Result: 

NEXT 

See step  7

1. Check for DTCs.

   Body Electrical > Clearance Warning > Trouble Codes 

   Result

   Result	Proceed to
   DTCs are output	A
   DTCs are not output (Problem symptom does not occur)	B
   DTCs are not output (Problem symptom occurs)	C

Result: 

B 

See step  9

Result: 

C 

See step  10

Result: 

A 

See step  8

1. Refer to Diagnostic Trouble Code Chart.

   Refer to DIAGNOSTIC TROUBLE CODE CHART [10/2020 - ] 

   NOTE:

   The clearance warning ECU assembly outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the parking support brake system are output, refer to Diagnostic Trouble Code Chart for the relevant systems.

   System	Proceed to
   Intuitive Parking Assist System	Refer to DIAGNOSTIC TROUBLE CODE CHART [10/2020 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  12

1. Refer to Symptom Simulation.

   Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2020 - 08/2021] , or refer to HOW TO PROCEED WITH TROUBLESHOOTING [08/2021 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  10

1. Refer to Problem Symptoms Table.

   Refer to PROBLEM SYMPTOMS TABLE [10/2020 - ] 

   Result

   Result	Proceed to
   Fault is not listed in Problem Symptoms Table	A
   Fault is listed in Problem Symptoms Table	B

Result: 

B 

See step  12

Result: 

A 

See step  11

1. Operation Check

   Refer to OPERATION CHECK [10/2020 - ] 

2. Terminals of ECU

   Refer to TERMINALS OF ECU [10/2020 - ] 

3. Data List / Active Test

   Refer to DATA LIST / ACTIVE TEST [10/2020 - ] 

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  12

Result

Result: 

NEXT 

See step  13

Result

Result: 

NEXT 

See step  14

Result

Result: 

NEXT 

See step  15

Result

Result: 

NEXT 

END