LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2018 >> Camry LE >> Repair and Diagnosis >> External Pages >> Different car >> Section 6 (Automatic Transmission System (UB80F) - Service Information (2 Of 2) (Except Hybrid)) >> Automatic Transaxle Assembly >> Removal [03/2020 - 10/2020] >> Caution / Notice / Hint

Caution / Notice / Hint

WARNING: This page is about a different car, the 2024 Toyota Camry, 2023 Toyota Camry, 2022 Toyota Camry, 2021 Toyota Camry, and 2020 Toyota Camry. However, it is still accessible from the selected car via links, so may be relevant.

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during automatic transaxle assembly removal/installation are shown below.

NECESSARY PROCEDURE AFTER PARTS REMOVED/INSTALLED/REPLACED

Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) Refer to INITIALIZATION [03/2017 - 10/2020]
Pre-collision system
Intelligent clearance sonar system*4
Memorize steering angle neutral point Parking assist monitor system Refer to INITIALIZATION [03/2017 - ]
Panoramic view monitor system Refer to INITIALIZATION [06/2017 - 10/2020]
Replacement of ECM Vehicle Identification Number (VIN) registration MIL comes on Refer to REGISTRATION [03/2017 - ]
ECU communication ID registration (Immobiliser system) Engine start function Refer to REGISTRATION [09/2019 - 08/2022] *1
Refer to REGISTRATION [09/2019 - ] *2
  • Replacement of engine assembly
  • Gas leak from exhaust system is repaired
 Inspection After Repair
  • Poor idle, etc.
  • Engine start function, etc.
 Refer to INITIALIZATION [03/2020 - ]
Replacement of automatic transaxle assembly
  1. Reset memory
  2. Input transaxle compensation code into ECM
  3. Perform road test to allow ECM to learn
  • Large shift shock
  • Deterioration of fuel efficiency
 Refer to INITIALIZATION [03/2020 - ] for UB80F Initialization
Refer to REGISTRATION [03/2020 - ] for UB80F Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
  1. Reset memory*3
  2. Transfer transaxle compensation code
  3. Perform road test to allow ECM to learn
Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
  1. Reset memory*3
  2. Reset transaxle compensation code
  3. Perform road test to allow ECM to learn
Replacement of ECM*1 Code registration (Smart key System (for Start Function))
  • Wireless door lock control system
  • Smart key system (for Entry Function)
  • Smart key system (for Start Function)
  • Steering lock function
 Refer to REGISTRATION [09/2019 - 08/2022]
Replacement of ECM*2 Code registration (Immobiliser system (w/o Smart Key System))
  • Wireless door lock control system
  • Engine start
 Refer to REGISTRATION [09/2019 - ]
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)		 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system for Initialization: Refer to INITIALIZATION [03/2017 - ]
for Calibration: Refer to CALIBRATION [06/2017 - 10/2020]
Replacement of front bumper assembly (w/ Panoramic view monitor system) Front television camera view adjustment Panoramic view monitor system for Initialization: Refer to INITIALIZATION [06/2017 - 10/2020]
for Calibration: Refer to CALIBRATION [06/2017 - 10/2020]
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
  • Television camera controller initialization
  • Adjust steering angle
  • Rear television camera assembly optical axis (Back camera position setting)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
  • VSC disabled or malfunctioning
  • DTCs are output
  • Slip indicator light illuminated
  • ABS warning light illuminated
 Refer to CALIBRATION [06/2017 - 10/2020] w/ Electric Parking Brake System
Refer to CALIBRATION [06/2017 - 10/2020] w/o Electric Parking Brake System
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly. Refer to INITIALIZATION [03/2020 - ]
  1. *1: w/ Smart Key System
  2. *2: w/o Smart Key System
  3. *3: When the ECM is replaced with a new one, reset memory is unnecessary.
  4. *4: When performing learning using the Techstream.

    Refer to CALIBRATION [06/2017 - 10/2020]

WARNING:
  • The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair information, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
    GTY566510Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a An Object Exceeding Weight Limit of Engine Lifter
  • To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
    GTY563663Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  • The automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair information, or the transmission jack may suddenly drop.
    GTY559497Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a An Object Exceeding Weight Limit of Transmission Jack
scientia non olet · About LEMON Manuals