LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2018 >> Camry LE >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Engine Mechanical System (A25A-FKS) - Service Information (2 Of 5) (Except Hybrid) >> Front Crankshaft Oil Seal >> Removal [03/2017 - 06/2017] >> Caution / Notice / Hint

Caution / Notice / Hint

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front crankshaft oil seal removal/installation are shown below.

NECESSARY PROCEDURE AFTER PARTS REMOVED/INSTALLED/REPLACED

Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) Refer to INITIALIZATION [03/2017 - 10/2020]
Pre-collision system
Memorize steering angle neutral point Parking Assist Monitor System Refer to INITIALIZATION [03/2017 - ]
Replacement of ECM Vehicle Identification Number (VIN) registration MIL comes on Refer to REGISTRATION [03/2017 - ]
ECU communication ID registration (Immobilizer system) Engine start function Refer to REGISTRATION [03/2017 - 09/2019] *1
Refer to REGISTRATION [03/2017 - 09/2019] *2
  • Gas leak from exhaust system is repaired
  • Replacement of air fuel ratio sensor
 Inspection After Repair
  • Poor idle, etc.
  • Engine start function, etc.
 Refer to INITIALIZATION [03/2017 - 09/2019]
Replacement of automatic transaxle assembly
  1. Reset memory
  2. Input transaxle compensation code into ECM
  3. Perform road test to allow ECM to learn
  • Large shift shock
  • Deterioration of fuel efficiency
 Refer to INITIALIZATION [03/2017 - 08/2018] for UB80E Initialization
Refer to REGISTRATION [03/2017 - ] for UB80E Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
  1. Reset memory*3
  2. Transfer transaxle compensation code
  3. Perform road test to allow ECM to learn
Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
  1. Reset memory*3
  2. Reset transaxle compensation code
  3. Perform road test to allow ECM to learn
Replacement of ECM*1 Code registration (Smart key System (for Start Function))
  • Wireless door lock control system
  • Smart key system (for Entry Function)
  • Smart key system (for Start Function)
  • Steering lock function
 Refer to REGISTRATION [03/2017 - 09/2019]
Replacement of ECM*2 Code registration (Immobilizer system (w/o Smart Key System))
  • Wireless door lock control system
  • Engine start
 Refer to REGISTRATION [03/2017 - 09/2019]
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)		 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system for Initialization: Refer to INITIALIZATION [03/2017 - ]
for Calibration: Refer to CALIBRATION [03/2017 - 06/2017]
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
  • VSC disabled or malfunctioning
  • DTCs are output
  • Slip indicator light illuminated
  • ABS warning light illuminated
 Refer to CALIBRATION [03/2017 - 06/2017]
  1. *1: w/ Smart Key System
  2. *2: w/o Smart Key System
  3. *3: When the ECM is replaced with a new one, reset memory is unnecessary.
NOTE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Refer to PRECAUTION [03/2017 - 06/2017]

scientia non olet · About LEMON Manuals