Speedometer Malfunction [06/2017 - 10/2020]: Procedure
- CHECK CAN COMMUNICATION SYSTEM
- Check if CAN communication DTCs are output.
Refer to DIAGNOSIS SYSTEM [06/2017 - 08/2018] , or refer to DIAGNOSIS SYSTEM [08/2018 - 09/2019] , or refer to DIAGNOSIS SYSTEM [09/2019 - 03/2020] , or refer to DIAGNOSIS SYSTEM [03/2020 - 10/2020]
Result
Result Proceed to DTCs are not output A DTCs are output B
Result:
B
GO TO CAN COMMUNICATION SYSTEM. Refer to HOW TO PROCEED WITH TROUBLESHOOTING [03/2017 - ]
Result:
A
See step 2
- Check if CAN communication DTCs are output.
- CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)
- Check if vehicle stability control system DTCs are output.
Chassis > ABS/VSC/TRAC/EPB > Trouble Codes
Result
Result Proceed to DTCs are not output A DTCs are output B
Result:
B
GO TO VEHICLE STABILITY CONTROL SYSTEM
w/o Electric Parking Brake System: Refer to DIAGNOSTIC TROUBLE CODE CHART [06/2017 - 10/2020]
w/ Electric Parking Brake System: Refer to DIAGNOSTIC TROUBLE CODE CHART [06/2017 - 03/2020] , or refer to DIAGNOSTIC TROUBLE CODE CHART [03/2020 - 10/2020]
Result:
A
See step 3
- Check if vehicle stability control system DTCs are output.
- PERFORM ACTIVE TEST USING TECHSTREAM (SPEEDOMETER OPERATION)
- Connect the Techstream to the DLC3.
- Turn the ignition switch to ON.
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Combination Meter / Active Test.
- Perform the Active Test according to the display on the Techstream.
Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note Speedometer Operation (0km/h, 0MPH) Speedometer 0km/h (0mph) OFF or ON - Speedometer Operation (40km/h, 40MPH) Speedometer 40 km/h (40 mph) OFF or ON The value displayed on the speedometer may deviate.
Reference mph*1:
40 → 39.5 to 42.3
Reference km/h*2:
40 → 38.7 to 43.2Speedometer Operation (80km/h, 80MPH) Speedometer 80 km/h (80 mph) OFF or ON The value displayed on the speedometer may deviate.
Reference mph*1:
80 → 80.2 to 83.4
Reference km/h*2:
80 → 79.3 to 84.3Speedometer Operation (120km/h, 120MPH) Speedometer 120 km/h (120 mph) OFF or ON The value displayed on the speedometer may deviate.
Reference mph*1:
120 → 121.1 to 124.3
Reference km/h*2:
120 → 120.2 to 125.2Speedometer Operation (160km/h, 160MPH) Speedometer 160 km/h (160 mph)*2 OFF or ON The value displayed on the speedometer may deviate.
Reference km/h*2:
160 → 161.1 to 166.1Speedometer Operation (200km/h, 200MPH) Speedometer 200 km/h (200 mph)*2 OFF or ON The value displayed on the speedometer may deviate.
Reference km/h*2:
200 → 202.0 to 207.0Speedometer Operation (240km/h, 240MPH) Speedometer 240 km/h (240 mph)*2 OFF or ON The value displayed on the speedometer may deviate.
Reference km/h*2:
240 → 242.9 to 247.9- *1: for Speedometer with Imperial Units for Main Scale
- *2: for Speedometer with Metric Units for Main Scale
Body Electrical > Combination Meter > Active Test
Tester Display Speedometer Operation (0km/h, 0MPH) Body Electrical > Combination Meter > Active Test
Tester Display Speedometer Operation (40km/h, 40MPH) Body Electrical > Combination Meter > Active Test
Tester Display Speedometer Operation (80km/h, 80MPH) Body Electrical > Combination Meter > Active Test
Tester Display Speedometer Operation (120km/h, 120MPH) Body Electrical > Combination Meter > Active Test
Tester Display Speedometer Operation (160km/h, 160MPH) Body Electrical > Combination Meter > Active Test
Tester Display Speedometer Operation (200km/h, 200MPH) Body Electrical > Combination Meter > Active Test
Tester Display Speedometer Operation (240km/h, 240MPH) OK
Speedometer indication is normal.
Result
Proceed to OK NG
Result:
OK
REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY). Refer to REMOVAL [06/2017 - 10/2020]
Result:
NG
REPLACE COMBINATION METER ASSEMBLY. Refer to REMOVAL [06/2017 - 10/2020]