LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2018 >> Camry LE >> Repair and Diagnosis >> Drivelines & Axles >> Driveshaft & Universal Joints >> Drive Shaft / Propeller Shaft - Service Information (Except Hybrid) >> FRONT DRIVE SHAFT ASSEMBLY (for A25A-FKS) >> Installation [03/2017 - 06/2017] >> Procedure

Installation [03/2017 - 06/2017]: Procedure

  1. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING 
    1. Install a new front drive shaft hole snap ring.
      NOTE:

      Face the end gap of the front drive shaft hole snap ring downward.

  2. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH 
    1. Coat the snap ring of the front drive inboard joint assembly with MP grease.
    2. Coat the splines of the front drive inboard joint assembly with Toyota genuine ATF WS.
    3. Coat the lip of the front drive shaft oil seal LH with MP grease and Toyota genuine oil seal side lip grease as shown in the illustration.

      HINT: 

      Apply a light coat of MP grease and Toyota genuine oil seal side lip grease to the entire circumference of the front drive shaft oil seal LH.

      GTY779876Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Cross Section of Front Drive Shaft Oil Seal LH
      MP Grease
      Toyota Genuine Oil Seal Side Lip Grease
    4. Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.
      GTY763130Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Face the end gap of the front drive shaft hole snap ring downward.
      • Do not damage the front drive shaft oil seal LH.
      • Do not damage the front axle inboard joint boot.
      • Make sure to center the front drive shaft assembly LH during installation to prevent damage to the front drive shaft hole snap ring.

      HINT: 

      Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.

    5. Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz) of Toyota Body Grease W to each of the 4 areas shown in the illustration.
      GTY773245Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Toyota Body Grease W
    6. Align the matchmarks and install the front drive shaft assembly LH to the front axle hub sub-assembly.
      GTY749339Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Matchmark
      NOTE:
      • Do not damage the front disc brake dust cover.
      • Do not damage the front axle outboard joint boot.
      • Check that there is no foreign matter on the deflector or contact surfaces.
      • Do not push the front axle assembly towards the outside of the vehicle any further than necessary.
      • Do not damage the deflector.
  3. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH 
    1. Coat the splines of the front drive inboard joint assembly with Toyota genuine ATF WS.
    2. Coat the lip of the front drive shaft oil seal RH with MP grease and Toyota genuine oil seal side lip grease as shown in the illustration.

      HINT: 

      Apply a light coat of MP grease and Toyota genuine oil seal side lip grease to the entire circumference of the front drive shaft oil seal RH.

      GTY779871Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Cross Section of Front Drive Shaft Oil Seal RH
      MP Grease
      Toyota Genuine Oil Seal Side Lip Grease
    3. Align the inboard joint splines, and securely insert the front drive shaft assembly RH.
      NOTE:
      • Do not damage the front drive shaft oil seal RH.
      • Do not damage the front axle inboard joint boot.
    4. Install the front drive shaft assembly RH with the 2 bolts.
      GTY763129Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 50.5 N*m (515 kgf*cm, 37 ft.*lbf) 

    5. Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz) of Toyota Body Grease W to each of the 4 areas shown in the illustration.
      GTY743393Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Toyota Body Grease W
    6. Align the matchmarks and install the front drive shaft assembly RH to the front axle hub sub-assembly.
      GTY751118Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Matchmark
      NOTE:
      • Do not damage the front disc brake dust cover.
      • Do not damage the front axle outboard joint boot.
      • Check that there is no foreign matter on the deflector or contact surfaces.
      • Do not push the front axle assembly towards the outside of the vehicle any further than necessary.
      • Do not damage the deflector.
  4. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 4

  5. INSTALL FRONT STABILIZER LINK ASSEMBLY 

    Refer to PROCEDURE - Step 14

  6. CONNECT TIE ROD ASSEMBLY 

    Refer to PROCEDURE - Step 9

  7. INSTALL FRONT SPEED SENSOR 

    Refer to PROCEDURE - Step 15

  8. INSTALL FRONT AXLE SHAFT NUT 
    1. Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.
      NOTE:
      • Make sure to perform this work even when using a new front drive shaft assembly.
      • Keep the threaded parts free of oil and foreign matter.
    2. Using a 30 mm deep socket wrench, install the front axle shaft nut.
      GTY763134Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 294 N*m (2998 kgf*cm, 217 ft.*lbf) 

      HINT: 

      Depress the brake pedal to prevent the drive shaft from rotating.

    3. Using a chisel and hammer, stake the front axle shaft nut.
  9. ADD AUTOMATIC TRANSAXLE FLUID 

    Refer to ADJUSTMENT [03/2017 - 08/2018]

  10. INSTALL FRONT WHEELS 

    Refer to PROCEDURE - Step 1

  11. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT 

    Refer to ADJUSTMENT [03/2017 - 06/2017]

  12. INSTALL FRONT FENDER APRON SEAL LH 

    Refer to PROCEDURE - Step 65

  13. INSTALL FRONT FENDER APRON SEAL RH 

    Refer to PROCEDURE - Step 66

  14. INSTALL NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 68

  15. INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 67

  16. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH 

    Refer to PROCEDURE - Step 69

  17. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH 

    Refer to PROCEDURE - Step 70

  18. CHECK FOR SPEED SENSOR SIGNAL 

    Refer to TEST MODE PROCEDURE [03/2017 - 06/2017]

scientia non olet · About LEMON Manuals