LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2018 >> Camry LE >> Repair and Diagnosis >> Brakes >> Mechanical - Hydraulic >> Brake System (Rear) (W/ Electric Parking Brake System) - Service Information (Except Hybrid) >> REAR BRAKE (w/ Electric Parking Brake System) >> Removal [06/2017 - ] >> Procedure

Removal [06/2017 - ]: Procedure

  1. PRECAUTION 

    Refer to PRECAUTION [06/2017 - ]

  2. REMOVE REAR WHEEL 

    Refer to PROCEDURE - Step 1

  3. PERFORM REAR BRAKE PAD REPLACEMENT MODE 

    Refer to TEST MODE PROCEDURE [06/2017 - 10/2020] , or refer to REAR BRAKE PAD REPLACEMENT MODE [10/2020 - ]

  4. DRAIN BRAKE FLUID 
    NOTE:

    If brake fluid leaks onto any painted surface, immediately wash it off.

  5. SEPARATE REAR FLEXIBLE HOSE 
    1. Remove the union bolt and gasket, and disconnect the rear flexible hose from the rear disc brake cylinder assembly.
      GTY764804Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY 

    Refer to PROCEDURE - Step 4

  7. REMOVE PARKING BRAKE ACTUATOR ASSEMBLY 

    Refer to PROCEDURE - Step 5

  8. REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY 
    1. Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and rear disc brake cylinder assembly.
      GTY758812Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Turn
      *b Hold
  9. REMOVE REAR DISC BRAKE PAD 
    1. Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.
      GTY764809Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT 

    Refer to PROCEDURE - Step 6

  11. REMOVE REAR DISC BRAKE PAD SUPPORT PLATE 
    1. Remove the 4 rear disc brake pad support plates from the rear disc brake cylinder mounting.
      NOTE:

      Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.

      GTY764745Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN 
    1. Remove the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin from the rear disc brake cylinder mounting.
      GTY743275Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Rear No. 1 Disc Brake Cylinder Slide Pin
      *2 Rear No. 2 Disc Brake Cylinder Slide Pin
    2. Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from the rear No. 2 disc brake cylinder slide pin.
      NOTE:

      Do not damage the rear No. 2 disc brake cylinder slide pin.

      GTY671959Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
  13. REMOVE REAR DISC BRAKE BUSHING DUST BOOT 
    1. Remove the 2 rear disc brake bushing dust boots from the rear disc brake cylinder mounting.
      GTY773860Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. REMOVE REAR DISC BRAKE CYLINDER MOUNTING 
    1. Remove the 2 bolts and rear disc brake cylinder mounting.
      GTY764744Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE REAR DISC 
    1. Put matchmarks on the rear disc and rear axle hub and bearing assembly.
      GTY745353Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Matchmark
    2. Remove the rear disc.
scientia non olet · About LEMON Manuals