LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2018 >> Camry LE >> Repair and Diagnosis >> Accessories & Equipment >> Seats >> Seats - Service Information (2 Of 2) (Except Hybrid) >> POWER SEAT SWITCH (for TMMK Made Power Seat) >> Inspection [06/2017 - ] >> Procedure

Inspection [06/2017 - ]: Procedure

  1. INSPECT FRONT POWER SEAT SWITCH LH 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      SLIDE SWITCH

      Tester Connection Condition Specified Condition
      4 - 6 Slide switch pressed
      (Forward)
      Below 1 Ω
      1 - 12
      4 - 12 Off
      1 - 12
      1 - 6 Slide switch pressed
      (Rearward)
      4 - 12
      FRONT VERTICAL SWITCH

      Tester Connection Condition Specified Condition
      7 - 6 Front vertical switch pressed
      (Up)
      Below 1 Ω
      11 - 12
      7 - 12 Off
      11 - 12
      11 - 6 Front vertical switch pressed
      (Down)
      7 - 12
      LIFTER SWITCH

      Tester Connection Condition Specified Condition
      8 - 6 Lifter switch pressed
      (Up)
      Below 1 Ω
      10 - 12
      10 - 12 Off
      8 - 12
      10 - 6 Lifter switch pressed
      (Down)
      8 - 12
      RECLINING SWITCH

      Tester Connection Condition Specified Condition
      5 - 6 Reclining switch pressed
      (Forward)
      Below 1 Ω
      11 - 6
      7 - 6
      3 - 12
      5 - 12 Off
      3 - 12
      3 - 6 Reclining switch pressed
      (Rearward)
      5 - 12
      10 - 6
      8 - 6
      LUMBAR SUPPORT SWITCH

      Tester Connection Condition Specified Condition
      9 - 6 Lumbar switch pressed
      (Hold)
      Below 1 Ω
      2 - 12
      2 - 12 Off
      9 - 12
      2 - 6 Lumbar switch pressed
      (Release)
      9 - 12

      If the result is not as specified, replace the front power seat switch LH.

      GTY774260Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Slide Switch (Forward)
      *b Slide Switch (Rearward)
      *c Front Vertical Switch (Up)
      *d Front Vertical Switch (Down)
      *e Lifter Switch (Up)
      *f Lifter Switch (Down)
      *g Reclining Switch (Forward)
      *h Reclining Switch (Rearward)
      *i Lumbar Support Switch (Hold)
      *j Lumbar Support Switch (Release)
      *k Component without harness connected
      (Front Power Seat Switch LH)
  2. INSPECT FRONT POWER SEAT SWITCH RH 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      SLIDE SWITCH

      Tester Connection Condition Specified Condition
      2 - 12 Slide switch pressed
      (Forward)
      Below 1 Ω
      5 - 6
      2 - 6 Off
      5 - 6
      2 - 6 Slide switch pressed
      (Rearward)
      5 - 12
      FRONT VERTICAL SWITCH

      Tester Connection Condition Specified Condition
      7 - 6 Front vertical switch pressed
      (Up)
      Below 1 Ω
      11 - 12
      11 - 6 Off
      7 - 6
      11 - 6 Front vertical switch pressed
      (Down)
      7 - 12
      LIFTER SWITCH

      Tester Connection Condition Specified Condition
      8 - 6 Lifter switch pressed
      (Up)
      Below 1 Ω
      10 - 12
      10 - 6 Off
      8 - 6
      10 - 6 Lifter switch pressed
      (Down)
      8 - 12
      RECLINING SWITCH

      Tester Connection Condition Specified Condition
      11 - 12 Reclining switch pressed
      (Forward)
      Below 1 Ω
      7 - 12
      1 - 12
      3 - 6
      1 - 6 Off
      3 - 6
      1 - 6 Reclining switch pressed
      (Rearward)
      10 - 12
      8 - 12
      3 - 12

      If the result is not as specified, replace the front power seat switch RH.

      GTY773987Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Slide Switch (Forward)
      *b Slide Switch (Rearward)
      *c Front Vertical Switch (Up)
      *d Front Vertical Switch (Down)
      *e Lifter Switch (Up)
      *f Lifter Switch (Down)
      *g Reclining Switch (Forward)
      *h Reclining Switch (Rearward)
      *i Component without harness connected
      (Front Power Seat Switch RH)