LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2018 >> Avalon XLE >> Repair and Diagnosis >> Accessories & Equipment >> Communication Devices >> Safety Connect System - Diagnostic Codes & Symptom Tests - (Except Hybrid) >> Safety Connect System >> DTC B1570: Manual (SOS) Switch Red Indicator Malfunction [10/2014 - ] >> Procedure

DTC B1570: Manual (SOS) Switch Red Indicator Malfunction [10/2014 - ]: Procedure

  1. CHECK DTC 
    1. Turn the engine switch off.
    2. Connect the Techstream to the DLC3.
    3. Turn the engine switch on (IG) and wait for 10 seconds.
    4. Turn the Techstream on.
    5. Perform "Health Check" and check for current DTCs (Refer to HEALTH CHECK [10/2014 - ] ).

      Result

      Result Proceed to
      DTC B1570, B1571 and B15C5 are output A
      DTC B1570 is output
      (DTC B1571 and B15C5 are not output)      		 B

    Result: 

    B 

    See step  6

    Result: 

    A 

    See step  2

  2. INSPECT ROOF CONSOLE BOX ASSEMBLY (RED INDICATOR) 
    1. Disconnect the N6 roof console box assembly connector.
      GTY599130Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect 2 dry-cell batteries (1.5 V each) in series.
    3. Connect the positive (+) lead to terminal N6-19 (IND1) and the negative (-) lead to terminal N6-16 (GND3) of the roof console box assembly connector.
    4. Check if the illumination for the manual (SOS) switch red indicator comes on.

      OK

      Red indicator comes on.

      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Roof Console Box Assembly)

    Result: 

    NG 

    REPLACE ROOF CONSOLE BOX ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - ROOF CONSOLE BOX ASSEMBLY) 
    1. Disconnect the E11 DCM (Telematics Transceiver) connector.
    2. Disconnect the N6 roof console box assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      E11-26 (SIG-) - N6-16 (GND3) Always Below 1 Ω
      E11-26 (SIG-) - Body ground Always 10 kΩ or higher
      E11-11 (IND1) - N6-19 (IND1) Always Below 1 Ω
      E11-11 (IND1) - Body ground Always 10 kΩ or higher

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. REPLACE DCM (TELEMATICS TRANSCEIVER) 
    1. Replace the DCM (Telematics Transceiver) (Refer to REMOVAL [10/2014 - ] ).
      NOTE:
      • The engine switch must be off.
      • Do not swap the DCM (Telematics Transceiver) with one from another vehicle.

    Result: 

    NEXT 

    See step  5

  5. PERFORM PRL UPDATE 
    1. Perform "PRL UPDATE" (Refer to PRL UPDATE [10/2014 - ] ).

    Result: 

    NEXT 

    PERFORM DCM ACTIVATION 

    (Refer to DCM ACTIVATION [10/2014 - ] )

  6. INSPECT ROOF CONSOLE BOX ASSEMBLY (MANUAL (SOS) SWITCH RED INDICATOR CONDITION) 
    1. Confirm the red indicator status after the engine switch is turned on (IG) (Refer to SYSTEM DESCRIPTION [10/2014 - ] ).

      Result

      Result Proceed to
      Red indicator remains off. A
      Red indicator remains on. B

    Result: 

    B 

    See step  10

    Result: 

    A 

    See step  7

  7. INSPECT ROOF CONSOLE BOX ASSEMBLY (RED INDICATOR INPUT VOLTAGE) 
    1. Remove the roof console box assembly but do not disconnect the connectors (Refer to REMOVAL [10/2014 - ] ).
      GTY610486Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the positive lead of a voltmeter to terminal N6-19 (IND1), and the negative lead to terminal N6-16 (GND3).
    3. Measure the voltage.

      Standard

      1.0 to 8.5 V for 2 seconds after the engine switch is turned on (IG).

      0 V when the engine switch is off.

      TEXT IN ILLUSTRATION

      *a Component with harness connected
      (Roof Console Box Assembly)

    Result: 

    OK 

    REPLACE ROOF CONSOLE BOX ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    NG 

    See step  8

  8. INSPECT DCM (TELEMATICS TRANSCEIVER) (RED INDICATOR OUTPUT VOLTAGE) 
    1. Remove the DCM (Telematics Transceiver) but do not disconnect the connectors (Refer to REMOVAL [10/2014 - ] ).
      GTY560914Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the positive lead of a voltmeter to terminal E11-11 (IND1), and the negative lead to body ground.
    3. Measure the voltage.

      Standard

      1.0 to 8.5 V for 2 seconds after the engine switch is turned on (IG).

      0 V when the engine switch is off.

      TEXT IN ILLUSTRATION

      *a Component with harness connected
      (DCM (Telematics Transceiver))

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    See step  9

  9. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - BODY GROUND) 
    1. Remove the DCM (Telematics Transceiver) but do not disconnect the connectors (Refer to REMOVAL [10/2014 - ] ).
      GTY560914Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      E11-11 (IND1) - Body ground Always 10 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Component with harness connected
      (DCM (Telematics Transceiver))

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  10

  10. REPLACE DCM (TELEMATICS TRANSCEIVER) 
    1. Replace the DCM (Telematics Transceiver) (Refer to REMOVAL [10/2014 - ] ).
      NOTE:
      • The engine switch must be off.
      • Do not swap the DCM (Telematics Transceiver) with one from another vehicle.

    Result: 

    NEXT 

    See step  11

  11. PERFORM PRL UPDATE 
    1. Perform "PRL UPDATE" (Refer to PRL UPDATE [10/2014 - ] ).

    Result: 

    NEXT 

    PERFORM DCM ACTIVATION 

    (Refer to DCM ACTIVATION [10/2014 - ] )

scientia non olet · About LEMON Manuals