Speedometer Malfunction [12/2012 - 10/2015]: Procedure

1. Check if a CAN communication system DTC is output.

   Refer to DIAGNOSIS SYSTEM [12/2012 - 11/2013] or DIAGNOSIS SYSTEM [11/2013 - 10/2015] .

   Result	Proceed to
   	CAN communication system DTC is not output
   	CAN communication system DTC is output

Result: 

CAN communication system DTC is output 

GO TO CAN COMMUNICATION SYSTEM.  Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - 10/2015] .

Result: 

CAN communication system DTC is not output 

See step  2

1. Check if a vehicle stability control system DTC is output.

   Refer to DTC CHECK / CLEAR [12/2012 - 10/2015] .

   Chassis > ABS/VSC/TRC > Trouble Codes 

   Result	Proceed to
   	DTC is not output
   	Vehicle stability control system DTC is output

Result: 

Vehicle stability control system DTC is output 

GO TO VEHICLE STABILITY CONTROL SYSTEM.  Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2012 - ] .

Result: 

DTC is not output 

See step  3

1. Using the Techstream, perform the Active Test.

   Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] .

   Body Electrical > Combination Meter > Active Test 

   Tester Display	Measurement Item	Control Range	Diagnostic Note
   Speed Meter Operation	Speedometer	OFF, 0, 40, 80, 120, 160 or 200 (km/h or mph)	Acceptable range (km/h or mph): [Control range → Speedometer display] for mph  40 → 40 to 43.5 80 → 80 to 84.5 120 → 100 to 125.5 for km/h (for Canada)  40 → 38 to 42 80 → 78 to 84 120 → 119 to 125 160 → 159 to 167 200 → 199 to 209 for km/h (except Canada)  40 → 41.7 to 46.2 80 → 83.4 to 88.4 120 → 125.1 to 130.6 160 → 166.2 to 173.2 200 → 207.7 to 215.7

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Speed Meter Operation

   OK

   Speedometer indication is normal.

   Result	Proceed to
   	OK
   	NG

Result: 

NG 

REPLACE COMBINATION METER ASSEMBLY.  Refer to REMOVAL [12/2012 - ] .

Result: 

OK 

See step  4

1. Using the Techstream, read the Data List.

   Refer to DATA LIST / ACTIVE TEST [12/2012 - 10/2015] .

   Body Electrical > Combination Meter > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Vehicle Speed Meter	Vehicle speed	Min.: 0 mph (0 km/h), Max.: 255 km/h (158 mph)	Almost same as actual vehicle speed measured using a speedometer tester	-

   Chassis > ABS/VSC/TRC > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Vehicle Speed	Vehicle speed	Min.: 0 mph (0 km/h), Max.: 326 km/h (202 mph)	Almost same as actual vehicle speed measured using a speedometer tester	-

   Body Electrical > Combination Meter > Data List 

   Tester Display
   Vehicle Speed Meter

   Chassis > ABS/VSC/TRC > Data List 

   Tester Display
   Vehicle Speed

   HINT: 

   • When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.
   • When the Data List values of the ECUs do not match, a signal output error of the brake actuator assembly (skid control ECU) or an internal malfunction of the combination meter assembly is suspected.

   Result	Proceed to
   	The Data List values of the ECUs match
   	The Data List values of the ECUs do not match

Result: 

The Data List values of the ECUs match 

REPLACE COMBINATION METER ASSEMBLY.  Refer to REMOVAL [12/2012 - ] .

Result: 

The Data List values of the ECUs do not match 

See step  5

1. Replace the combination meter assembly with a new or normally functioning one.

   Refer to REMOVAL [12/2012 - ] .

2. Check the speedometer operation.

   OK

   The operation of the speedometer returns to normal.

   Result	Proceed to
   	OK
   	NG

Result: 

OK 

END (COMBINATION METER ASSEMBLY WAS DEFECTIVE) 

Result: 

NG 

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU). 

Refer to REMOVAL [12/2012 - 10/2015] .