LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2017 >> RAV4 Limited, FWD >> Repair and Diagnosis >> Engine Performance >> Testing & Diagnosis >> SFI System [2AR-FE] (Diagnostic Codes) (Except Hybrid) (1 Of 7) >> SFI System >> DTC P0102: Mass or Volume Air Flow Circuit Low Input; DTC P0103: Mass or Volume Air Flow Circuit High Input [12/2012 - ] >> Procedure

DTC P0102: Mass or Volume Air Flow Circuit Low Input; DTC P0103: Mass or Volume Air Flow Circuit High Input [12/2012 - ]: Procedure

  1. READ OUTPUT DTC (DTC P0102 OR P0103) 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
    5. Read the DTCs.

      Powertrain > Engine and ECT > Trouble Codes 

      Result

      Result Proceed to
      DTC P0102 is output A
      DTC P0103 is output B

    Result: 

    B 

    See step  6

    Result: 

    A 

    See step  2

  2. CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY) 
    1. Disconnect the mass air flow meter sub-assembly connector.
      GTY364731Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
      *a Front view of wire harness connector
      (to Mass Air Flow Meter Sub-assembly)
    2. Turn the ignition switch to ON.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      B1-3 (+B) - Body ground Ignition switch ON 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  5

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM) 
    1. Disconnect the mass air flow meter sub-assembly connector.
    2. Disconnect the ECM connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B1-5 (VG) - B77-91 (VG) Always Below 1 Ω
      B1-4 (E2G) - B77-92 (E2G) Always Below 1 Ω
      B1-5 (VG) or B77-91 (VG) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. INSPECT MASS AIR FLOW METER SUB-ASSEMBLY 
    1. Inspect the mass air flow meter sub-assembly, referring to the On-vehicle Inspection for Mass Air Flow Meter.

      Refer to ON-VEHICLE INSPECTION [12/2012 - ]

    2. Inspect the mass air flow meter sub-assembly, referring to the Inspection for Mass Air Flow Meter.

      Refer to INSPECTION [12/2012 - ]

    3. Inspect the function of the mass air flow meter sub-assembly.
      1. Connect the Techstream to the DLC3.
      2. Turn the ignition switch to ON.
      3. Turn the Techstream on.
      4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / MAF.

        Powertrain > Engine and ECT > Data List 

        Tester Display
        MAF
      5. Start the engine.
      6. Check that the MAF value changes when the engine is raced.

        OK

        The reading changes.

        HINT: 

        Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

        Refer to INITIALIZATION [12/2012 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ECM. Refer to  REMOVAL [12/2012 - ] 

    Result: 

    NG 

    REPLACE MASS AIR FLOW METER SUB-ASSEMBLY. Refer to  REMOVAL [12/2012 - ] 

  5. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - EFI-MAIN NO. 1 RELAY) 
    1. Disconnect the mass air flow meter sub-assembly connector.
    2. Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B1-3 (+B) - EFI-MAIN NO. 1 relay terminal 3 Always Below 1 Ω
      B1-3 (+B) or EFI-MAIN NO. 1 relay terminal 3 - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    GO TO ECM POWER SOURCE CIRCUIT. Refer to  ECM Power Source Circuit [12/2012 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  6. CHECK HARNESS AND CONNECTOR (SENSOR GROUND) 
    1. Disconnect the mass air flow meter sub-assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B1-4 (E2G) - Body ground Always Below 1 Ω

      HINT: 

      Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

      Refer to INITIALIZATION [12/2012 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE MASS AIR FLOW METER SUB-ASSEMBLY. Refer to  REMOVAL [12/2012 - ] 

    Result: 

    NG 

    See step  7

  7. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM) 
    1. Disconnect the mass air flow meter sub-assembly connector.
    2. Disconnect the ECM connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B1-4 (E2G) - B77-92 (E2G) Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ECM. Refer to  REMOVAL [12/2012 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals