DTC P0E71-344: Generator Torque Delivered Performance [08/2015 - ]: Procedure
- CHECK DTC OUTPUT (HYBRID CONTROL)
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
- Check if DTCs are output.
Result
Result Proceed to P0E71-344 only is output. A Any of the following DTCs are also output. B DTC No. Relevant Diagnosis P06B0-163 Sensor Power Supply "A" Circuit/Open P06D6-511 Sensor Reference Voltage "F" Circuit/Open P06E6-164 Sensor Power Supply "C" Circuit/Open P0A1A-151, 166, 517, 658, 791, 809 Generator Control Module P0A1B-198, 503, 505, 547, 554, 786, 794, 806 Drive Motor "A" Control Module P0A1D (all INF codes)*1 Hybrid Powertrain Control Module P0A3F-243 Drive Motor "A" Position Sensor Circuit P0A40-500, 504, 506, 549, 556, 808 Drive Motor "A" Position Sensor Circuit Range/Performance P0A41-245 Drive Motor "A" Position Sensor Circuit Low P0A4B-253 Generator Position Sensor Circuit P0A4C-513, 518, 811 Generator Position Sensor Circuit Range/Performance P0A4D-255 Generator Position Sensor Circuit Low P0A78-279, 287, 548, 555, 807 Drive Motor "A" Inverter Performance P0A7A-203, 325, 810 Generator Inverter Performance P0AA6 (all INF codes)*1 Hybrid Battery Voltage System Isolation Fault P0BEA-290 Drive Motor "A" Phase V Current Sensor Circuit Range/Performance P0BEE-298 Drive Motor "A" Phase W Current Sensor Circuit Range/Performance P0C76-523 Hybrid Battery System Discharge Time Too Long P0D2E-586 Drive Motor "A" Inverter Voltage Sensor Circuit Range/Performance P0D2F-266 Drive Motor "A" Inverter Voltage Sensor Circuit Low P0D30-267 Drive Motor "A" Inverter Performance P0E05-328 Generator Phase V Current Sensor Circuit Range/Performance P0E09-336 Generator Phase W Current Sensor Circuit Range/Performance P0E32-585 DC/DC Converter Voltage Sensor "A" Range/Performance P0E33-589 DC/DC Converter Voltage Sensor "A" Low P0E34-590 DC/DC Converter Voltage Sensor "A" High P1C2A-155 Generator A/D Converter Circuit P1C2B-192 Drive Motor "A" A/D Converter Circuit P1C2D-587 Hybrid Battery Voltage / DC/DC Converter Voltage Correlation P1C3C-294 Drive Motor "A" Phase V Current Sensor Correlation P1C3D-302 Drive Motor "A" Phase W Current Sensor Correlation P1C3E-333 Generator Phase V Current Sensor Correlation P1C3F-341 Generator Phase W Current Sensor Correlation P1C4A-288 Drive Motor "A" Phase V Current Sensor Sub Circuit Range/Performance P1C4F-296 Drive Motor "A" Phase W Current Sensor Sub Circuit Range/Performance P1C54-326 Generator Phase V Current Sensor Sub Circuit Range/Performance P1C59-334 Generator Phase W Current Sensor Sub Circuit Range/Performance P1C6D-501 Drive Motor "A" Phase V Current Sensor Offset Range/Performance P1C6E-502 Drive Motor "A" Phase W Current Sensor Offset Range/Performance P1C71-515 Generator Phase V Current Sensor Offset Range/Performance P1C72-516 Generator Phase W Current Sensor Offset Range/Performance P1C73-512 Sensor Standard Voltage "F" Circuit/Open P1CA6-156 Generator Control Module Malfunction P1CA7-193 Drive Motor Control Module Malfunction P1CAC-200 Generator Position Sensor Angle Malfunction P1CAD-168 Drive Motor "A" Position Sensor Angle Malfunction P1CAF-792 Generator Position Sensor REF Signal Cycle Malfunction P1CB0-795 Drive Motor "A" Position Sensor REF Signal Cycle Malfunction P1CB2-793 Generator Position Sensor REF Signal Stop Malfunction P1CB3-796 Drive Motor "A" Position Sensor REF Signal Stop Malfunction P3004-132 Power Cable Malfunction P3133-659 Communication Error from Generator to Drive Motor "A" P3134-661 Communication Error from Drive Motor "A" to Generator P3233-750 Open or Short to B+ in Blocking of HV Gate Connection HINT:
- *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.
- P0E71-344 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.
- Turn the power switch off.
B → Refer to 7
A: Go to next step
- CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR). Refer to PROCEDURE - Step 4
NG → CONNECT SECURELY
OK: Go to next step
- CHECK INVERTER WITH CONVERTER ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION). Refer to PROCEDURE - Step 9
B → REPLACE MALFUNCTIONING PARTS
C → CONNECT SECURELY
A: Go to next step
- CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1). Refer to PROCEDURE - Step 11
NG → Refer to 5
OK → Refer to 9
- CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION). Refer to PROCEDURE - Step 26
B → REPLACE MALFUNCTIONING PARTS
C → CONNECT SECURELY
A: Go to next step
- CHECK GENERATOR CABLE. Refer to PROCEDURE - Step 27
NG → Refer to 10
OK → Refer to 8
- GO TO DTC CHART (HYBRID CONTROL SYSTEM). Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2015 - ]
- REPLACE HYBRID VEHICLE GENERATOR ASSEMBLY. Refer to COMPONENTS [08/2015 - ]
- REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS. Refer to DTC CHECK / CLEAR [08/2015 - ]
- REPLACE GENERATOR CABLE. Refer to COMPONENTS [08/2015 - ]