Installation [11/2015 - 12/2018]: Procedure

INSTALL HV FLOOR UNDER WIRE

WARNING:

Wear insulated gloves.

Engage the clamp (B).

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install a new clamp (A).

Insert the HV floor under wire into the floor panel hole and engage the grommet.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install 3 new clamps in the order shown in the illustration.

Fig 1: HV Floor Under Wire Clamps Tightening Sequence
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install the HV floor under wire with the 2 nuts.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf)

CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY
1. Connect the No. 2 parking brake cable assembly with the 2 bolts.
  Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf)
INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Refer to INSTALLATION [11/2015 - 12/2018]
INSTALL FRONT FLOOR COVER RH
HINT:

Perform the same procedure as for the front floor cover LH.

Refer to PROCEDURE - Step 12
INSTALL NO. 1 FLOOR UNDER COVER ASSEMBLY
Refer to PROCEDURE - Step 11
CONNECT HV FLOOR UNDER WIRE
WARNING:
Wear insulated gloves.
1. Connect the shield ground to the HV battery.
2. Connect the 2 HV battery junction block assembly connectors.
  NOTE:
  Make sure that the connectors are connected securely.
INSTALL NO. 1 HV BATTERY COVER PANEL RH
- for NICKEL METAL HYDRIDE BATTERY:
  Refer to PROCEDURE - Step 14
- for LITHIUM-ION BATTERY:
  Refer to PROCEDURE - Step 8
INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY
- for NICKEL METAL HYDRIDE BATTERY:
  Refer to PROCEDURE - Step 16
- for LITHIUM-ION BATTERY:
  Refer to PROCEDURE - Step 10
INSTALL REAR UNDER COVER
- for NICKEL METAL HYDRIDE BATTERY:
  Refer to PROCEDURE - Step 17
- for LITHIUM-ION BATTERY:
  Refer to PROCEDURE - Step 11
INSTALL REAR UNDER SIDE COVER LH
Refer to PROCEDURE - Step 30
INSTALL REAR DOOR SCUFF PLATE LH
Refer to PROCEDURE - Step 47
INSTALL REAR UNDER SIDE COVER RH
HINT:

Use the same procedure as for the LH side.

Refer to PROCEDURE - Step 40
INSTALL REAR DOOR SCUFF PLATE RH
HINT:

Use the same procedure as for the LH side.

Refer to PROCEDURE - Step 57
INSTALL REAR SEAT CUSHION LOCK HOOK
Refer to PROCEDURE - Step 1
INSTALL REAR SEAT CUSHION ASSEMBLY
Refer to PROCEDURE - Step 2
CONNECT HV FLOOR UNDER WIRE
Refer to PROCEDURE - Step 12

CONNECT ENGINE WIRE

WARNING:

Wear insulated gloves.

NOTE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.

Engage the 2 clamps and connect the engine wire.
Install the bolt.
Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf)

Connect the 2 inverter with converter assembly connectors and move each lock lever as shown in the illustration.

NOTE:

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.
Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connectors.
Do not touch the waterproof seal or terminals of the connector.

INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
Refer to PROCEDURE - Step 72 [11/2015 - 08/2016] Refer to PROCEDURE - Step 72 [08/2016 - 12/2018]
INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
Refer to PROCEDURE - Step 14
INSTALL COWL BODY MOUNTING REINFORCEMENT LH
Refer to PROCEDURE - Step 15
INSTALL WATER GUARD PLATE LH
Refer to PROCEDURE - Step 16
INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL
Refer to PROCEDURE - Step 17
INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
Refer to INSTALLATION [11/2015 - ]
INSTALL SERVICE PLUG GRIP
Refer to INSTALLATION [11/2015 - ]