Removal [11/2015 - 12/2018]: Procedure
- PRECAUTION NOTE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Refer to PRECAUTION [11/2015 - 11/2017] Refer to PRECAUTION [11/2017 - 12/2018]
- REMOVE SERVICE PLUG GRIP
Refer to REMOVAL [11/2015 - 12/2018]
- REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
Refer to REMOVAL [11/2015 - ]
- REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL
Refer to PROCEDURE - Step 3
- REMOVE WATER GUARD PLATE LH
Refer to PROCEDURE - Step 4
- REMOVE COWL BODY MOUNTING REINFORCEMENT LH
Refer to PROCEDURE - Step 5
- REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
Refer to PROCEDURE - Step 6
- REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
Refer to PROCEDURE - Step 13 [11/2015 - 08/2016] Refer to PROCEDURE - Step 13 [08/2016 - 12/2018]
- DISCONNECT ENGINE WIRE
Refer to PROCEDURE - Step 9
- REMOVE CONNECTOR COVER ASSEMBLY
Refer to PROCEDURE - Step 16
- CHECK TERMINAL VOLTAGE
Refer to PROCEDURE - Step 17
- INSTALL CONNECTOR COVER ASSEMBLY
Refer to PROCEDURE - Step 12
- CONNECT ENGINE WIRE
See step 17
- INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
Refer to PROCEDURE - Step 72 [11/2015 - 08/2016] Refer to PROCEDURE - Step 72 [08/2016 - 12/2018]
- INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
Refer to PROCEDURE - Step 14
- INSTALL COWL BODY MOUNTING REINFORCEMENT LH
Refer to PROCEDURE - Step 15
- INSTALL WATER GUARD PLATE LH
Refer to PROCEDURE - Step 16
- INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL
Refer to PROCEDURE - Step 17
- INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
Refer to INSTALLATION [11/2015 - ]
- REMOVE REAR SEAT CUSHION ASSEMBLY
Refer to PROCEDURE - Step 7
- REMOVE REAR SEAT CUSHION LOCK HOOK
Refer to PROCEDURE - Step 8
- REMOVE REAR DOOR SCUFF PLATE LH
Refer to PROCEDURE - Step 18
- REMOVE REAR UNDER SIDE COVER LH
Refer to PROCEDURE - Step 35
- REMOVE REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
Refer to PROCEDURE - Step 28
- REMOVE REAR UNDER SIDE COVER RH
HINT:
Use the same procedure as for the LH side.
Refer to PROCEDURE - Step 46
- REMOVE REAR UNDER COVER
Refer to PROCEDURE - Step 26
- REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY
Refer to PROCEDURE - Step 27
- REMOVE BATTERY COOLING BLOWER ASSEMBLY
See step 9
- REMOVE NO. 1 HV BATTERY COVER PANEL RH
Refer to PROCEDURE - Step 29
- DISCONNECT HV FLOOR UNDER WIRE
Refer to PROCEDURE - Step 30
- DISCONNECT FLOOR WIRE
Refer to PROCEDURE - Step 31
- REMOVE NO. 1 HYBRID BATTERY EXHAUST DUCT
Refer to PROCEDURE - Step 32
- DISCONNECT FLOOR WIRE
Refer to PROCEDURE - Step 33
- REMOVE UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY
Refer to PROCEDURE - Step 34
- REMOVE NO. 1 HV BATTERY SHIELD PANEL
Refer to PROCEDURE - Step 35
- REMOVE HYBRID BATTERY TERMINAL BLOCK WARNING:
Be sure to wear insulated gloves and protective goggles.