LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2017 >> Prius Three Touring >> Repair and Diagnosis >> Hybrid/Electric Powertrain >> Testing and Diagnosis >> Hybrid Control System (Nickel Metal Hydride) - Diagnostic Codes (6 Of 8) >> HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) >> DTC P272C-81: Park Pawl Motor Invalid Serial Data Received [06/2021 -] >> Procedure

DTC P272C-81: Park Pawl Motor Invalid Serial Data Received [06/2021 -]: Procedure

  1. CHECK DTC OUTPUT (HYBRID CONTROL) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
    4. Check if DTCs are output.

      Powertrain > Hybrid Control > Trouble Codes 

      Result

      Result Proceed to
      None of the DTCs in the table below are output. A
      Any of the DTCs in the table below are output. B
      Relevant DTC
      P0606-47 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
      P060A-29 Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid
      P060A-44 Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure
      P060A-45 Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure
      P060A-47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
      P060A-49 Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure
      P0688-1F ECM/PCM Power Relay Sense Circuit Intermittent
    5. Turn the power switch off.

    Result: 

    B 

    GO TO DTC CHART (HYBRID CONTROL SYSTEM). Refer to  DIAGNOSTIC TROUBLE CODE CHART [06/2021 -] 

    Result: 

    A 

    See step  2

  2. CHECK FREEZE FRAME DATA (HYBRID CONTROL) 
    1. Connect the Techstream to the DLC3.
    2. Release the brake pedal and turn the power switch on (IG).

      HINT: 

      Do not turn the power switch on (READY).

    3. Read the freeze frame data of DTC P272C-81.

      Powertrain > Hybrid Control > DTC (P272C-81) > Freeze Frame Data 

      Tester Display
      BATT Voltage for Transmission Control System

      Result

      Result Proceed to
      The value of BATT Voltage for Transmission Control System is 9 V or more A
      The value of BATT Voltage for Transmission Control System is less than 9 V B
    4. Turn the power switch off.

    Result: 

    B 

    REPLACE AUXILIARY BATTERY. Refer to  REMOVAL [07/2020 -] 

    Result: 

    A 

    See step  3

  3. CLEAR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
    4. Clear the DTCs.

      Powertrain > Hybrid Control > Clear DTCs 

    5. Disconnect the Techstream from the DLC3.
    6. Turn the power switch off.
    7. Leave the vehicle as is for 60 seconds or more.
      NOTE:
      • Do not connect the Techstream.
      • Do not depress brake pedal.
      • Do not open/close any of the doors.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  4

  4. CHARGE AUXILIARY BATTERY 
    1. Charge the auxiliary battery.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  5

  5. CHECK DTC OUTPUT (SIMULATION TEST) 
    1. Connect the Techstream to the DLC3.
    2. Release the brake pedal and turn the power switch on (IG).

      HINT: 

      Do not turn the power switch on (READY).

    3. Depress the brake pedal and move the shift lever to select neutral (N).
    4. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
    5. Check if DTCs are output.

      Powertrain > Hybrid Control > Trouble Codes 

      Result

      Result Proceed to
      P272C-81 is output A
      P272C-81 is not output B
    6. Turn the power switch off.

    Result: 

    B 

    END (AUXILIARY BATTERY WAS INSUFFICIENTLY CHARGED) 

    Result: 

    A 

    See step  6

  6. CHECK P POSITION SWITCH (INDICATOR LIGHT) 
    1. Turn the power switch on (IG).
    2. Depress the brake pedal and move the shift lever to N.
    3. Press the P position switch (transmission shift main switch) and check the status of the indicator light.

      Result

      Condition of Indicator Light Proceed to
      Other than below. A
      Indicator light flashes. B
    4. Turn the power switch off.

    Result: 

    A 

    REPLACE HYBRID VEHICLE CONTROL ECU. Refer to  REMOVAL [07/2020 -] 

    Result: 

    B 

    See step  7

  7. CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY 
    1. Apply the parking brake.
    2. Disconnect the shift control actuator assembly connector.
    3. Remove the 3 shift control actuator bolts.

      Refer to COMPONENTS [11/2015 -]

    4. Slightly pull the shift control actuator assembly away from the hybrid vehicle transaxle.
    5. Wrap the shaft with a piece of cloth and check that it cannot be rotated in either direction by hand.
      GTY751446Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Lock
      *b Unlock

      OK

      The shaft cannot be rotated by hand.

      NOTE:

      Do not use tools, such as pliers, to perform this step.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HYBRID VEHICLE CONTROL ECU. Refer to  REMOVAL [07/2020 -] 

    Result: 

    NG 

    REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY. Refer to  REMOVAL [07/2020 -] 

scientia non olet · About LEMON Manuals