LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2017 >> Highlander XLE, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 49 (Engine Control System (2GR-FXE) (Service Information) (Hybrid)) >> Heated Oxygen Sensor >> Installation [02/2014 - 11/2016] >> Procedure

Installation [02/2014 - 11/2016]: Procedure

WARNING: This page is about a different car, the 2016 Toyota Highlander, 2015 Toyota Highlander, and 2014 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL HEATED OXYGEN SENSOR (for Bank 1) 

    HINT: 

    Perform "Inspection After Repair" after replacing a heated oxygen sensor.

    Refer to INITIALIZATION [02/2014 - 11/2016]

    1. Using SST, install the heated oxygen sensor to the front No. 3 exhaust pipe sub-assembly.
      GTY425100Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Length of SST 30 mm (1.18 in.)
      *b Length of Torque Wrench 260 mm (10.2 in.)
      • SST: 09224-00010 

      without SST [Torque (N*m (kgf*cm, ft.*lbf))] 

      Torque: 44 N*m (449 kgf*cm, 32 ft.*lbf) 

      with SST [Reading of Torque wrench (N*m (kgf*cm, ft.*lbf))] 

      Torque: 39 N*m (398 kgf*cm, 29 ft.*lbf) 

      NOTE:

      If the heated oxygen sensor has been struck or dropped, replace it.

      HINT: 

      • This torque value is effective when SST is parallel to the torque wrench.
      • The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).
      • The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 260 mm (10.2 in.).
      • If using a torque wrench with a different length, or connecting the torque wrench and SST at an angle, refer to the alternate torque values.

        Refer to PRECAUTION [02/2014 - 11/2016]

    2. Connect the heated oxygen sensor connector.
    3. Engage the 3 wire harness clamps.
  2. INSTALL FRONT FLOOR COVER LH 

    Refer to PROCEDURE - Step 14

  3. INSTALL HEATED OXYGEN SENSOR (for Bank 2) 

    HINT: 

    Perform "Inspection After Repair" after replacing a heated oxygen sensor.

    Refer to INITIALIZATION [02/2014 - 11/2016]

    1. Using SST, install the heated oxygen sensor to the front exhaust pipe assembly.
      • SST: 09224-00010 

      without SST [Torque (N*m (kgf*cm, ft.*lbf))] 

      Torque: 44 N*m (449 kgf*cm, 32 ft.*lbf) 

      with SST [Reading of Torque wrench (N*m (kgf*cm, ft.*lbf))] 

      Torque: 39 N*m (398 kgf*cm, 29 ft.*lbf) 

      NOTE:

      If the heated oxygen sensor has been struck or dropped, replace it.

      HINT: 

      • This torque value is effective when SST is parallel to the torque wrench.
      • The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).
      • The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 260 mm (10.2 in.).
      • If using a torque wrench with a different length, or connecting the torque wrench and SST at an angle, refer to the alternate torque values.

        Refer to PRECAUTION [02/2014 - 11/2016]

      GTY434174Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Length of SST 30 mm (1.18 in.)
      *b Length of Torque Wrench 260 mm (10.2 in.)
    2. Connect the heated oxygen sensor connector.
    3. Engage the 3 wire harness clamps.
  4. INSPECT FOR EXHAUST GAS LEAK 

    Refer to PROCEDURE - Step 14

  5. PERFORM INITIALIZATION 
    1. Perform "Inspection After Repair" after replacing a heated oxygen sensor.

      Refer to INITIALIZATION [02/2014 - 11/2016]

scientia non olet · About LEMON Manuals