LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2017 >> Highlander XLE, FWD >> Repair and Diagnosis >> Accessories & Equipment >> Warning Systems >> Park Assist & Monitoring System - Diagnostic Codes & Symptom Tests - (Except Hybrid) >> Parking Assist Monitor System >> DTC C1622: Back Camera Disconnected [12/2013 - 11/2016] >> Procedure

DTC C1622: Back Camera Disconnected [12/2013 - 11/2016]: Procedure

  1. CONFIRM MODEL 
    1. Choose the model to be inspected.

      Result

      Result Proceed to
      for Navigation Receiver Type A
      for Radio and Display Type B

    Result:  2

    B 

    See step  5

    Result:  1

    A 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY) 
    1. Disconnect the X12 television camera assembly connector.
    2. Disconnect the F117 navigation receiver assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      X12-6 (CB+) - F117-11 (CA+) Always Below 1 Ω
      X12-3 (CV+) - F117-12 (V+) Always Below 1 Ω
      X12-2 (CV-) - F117-24 (V-) Always Below 1 Ω
      X12-5 (CGND) - F117-23 (CGND) Always Below 1 Ω
      X12-6 (CB+) - Body ground Always 10 kΩ or higher
      X12-3 (CV+) - Body ground Always 10 kΩ or higher
      X12-2 (CV-) - Body ground Always 10 kΩ or higher
      X12-5 (CGND) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result:  1

    OK 

    See step  3

  3. INSPECT NAVIGATION RECEIVER ASSEMBLY (V-, CGND, CA+) 
    1. Reconnect the F117 navigation receiver assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F117-24 (V-) - Body ground Always Below 1 Ω
      F117-23 (CGND) - Body ground Always Below 1 Ω
      GTY440976Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Navigation Receiver Assembly)
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      F117-11 (CA+) - F117-23 (CGND) Engine switch on (ACC) 5.5 to 7.05 V

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPLACE NAVIGATION RECEIVER ASSEMBLY. Refer to  REMOVAL [12/2013 - ] 

    Result:  1

    OK 

    See step  4

  4. INSPECT NAVIGATION RECEIVER ASSEMBLY (V+, GND1) 
    1. Reconnect the X12 television camera assembly connector.
    2. Using an oscilloscope, check the waveform of the television camera assembly.
      GTY425433Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Navigation Receiver Assembly)

      HINT: 

      A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.

      OK

      Waveform is similar to that shown in the illustration.

      Item Content
      Measurement terminal F117-12 (V+) - F114-7 (GND1)
      Measurement setting 200 mV/DIV., 50 μs./DIV.
      Condition Engine switch on (IG), shift lever in R

      HINT: 

      • The video waveform changes according to the image sent by the television camera assembly.
      • The video waveform is constantly output when the engine switch is on (ACC).
      GTY436283Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Waveform 1 (camera lens is not covered, displaying an image)
      *b Waveform 2 (camera lens is covered, blacking out the screen)
      *c Synchronization Signal
      *d Video Waveform

      Result

      Proceed to
      OK
      NG

    Result:  1

    OK 

    REPLACE NAVIGATION RECEIVER ASSEMBLY. Refer to  REMOVAL [12/2013 - ] 

    Result:  2

    NG 

    REPLACE TELEVISION CAMERA ASSEMBLY. Refer to  REMOVAL [12/2013 - ] 

  5. CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY) 
    1. Disconnect the X12 television camera assembly connector.
    2. Disconnect the F72 radio and display receiver assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      X12-6 (CB+) - F72-11 (CA+) Always Below 1 Ω
      X12-3 (CV+) - F72-12 (V+) Always Below 1 Ω
      X12-2 (CV-) - F72-24 (V-) Always Below 1 Ω
      X12-5 (CGND) - F72-23 (CGND) Always Below 1 Ω
      X12-6 (CB+) - Body ground Always 10 kΩ or higher
      X12-3 (CV+) - Body ground Always 10 kΩ or higher
      X12-2 (CV-) - Body ground Always 10 kΩ or higher
      X12-5 (CGND) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result:  1

    OK 

    See step  6

  6. INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (V-, CGND, CA+) 
    1. Reconnect the F72 radio and display receiver assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F72-24 (V-) - Body ground Always Below 1 Ω
      F72-23 (CGND) - Body ground Always Below 1 Ω
      GTY454128Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Radio and Display Receiver Assembly)
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      F72-11 (CA+) - F72-23 (CGND) Engine switch on (ACC) 5.5 to 7.05 V

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [12/2013 - ] 

    Result:  1

    OK 

    See step  7

  7. INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (V+, GND1) 
    1. Reconnect the X12 television camera assembly connector.
    2. Using an oscilloscope, check the waveform of the television camera assembly.
      GTY450757Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Radio and Display Receiver Assembly)

      HINT: 

      A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.

      OK

      Waveform is similar to that shown in the illustration.

      Item Content
      Measurement terminal F72-12 (V+) - F69-7 (GND1)
      Measurement setting 200 mV/DIV., 50 μs./DIV.
      Condition Engine switch on (IG), shift lever in R

      HINT: 

      • The video waveform changes according to the image sent by the television camera assembly.
      • The video waveform is constantly output when the engine switch is on (ACC).
      GTY436283Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Waveform 1 (camera lens is not covered, displaying an image)
      *b Waveform 2 (camera lens is covered, blacking out the screen)
      *c Synchronization Signal
      *d Video Waveform

      Result

      Proceed to
      OK
      NG

    Result:  1

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [12/2013 - ] 

    Result:  2

    NG 

    REPLACE TELEVISION CAMERA ASSEMBLY. Refer to  REMOVAL [12/2013 - ] 

scientia non olet · About LEMON Manuals