Data List / Active Test [11/2016 - ]

HINT: 

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Main Body / Data List.
5. Read the Data List according to the display on the Techstream.

   Body Electrical > Main Body > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Auto High Beam Main Switch	Automatic high beam switch signal	OFF or ON	OFF: Automatic high beam switch not pressed ON: Automatic high beam switch pressed	-
   Dimmer SW	Dimmer switch high position signal	OFF or ON	OFF: Dimmer switch in low position ON: Dimmer switch in high or high flash position	-
   Auto Light SW	Light control switch AUTO position signal	OFF or ON	OFF: Light control switch not in AUTO position ON: Light control switch in AUTO position	-
   Head Light SW (Head)	Light control switch head position signal	OFF or ON	OFF: Light control switch not in head position ON: Light control switch in head position	-
   Light Sensor Illuminance	Light control sensor illuminance	0 to 8191 lx	Value is output according to ambient light level	-
   Auto H Beam STS0	Automatic high beam sensor current state	Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err	Condition can be displayed	Undetec: Undetected CAM NA: Camera detection malfunction* No sens: No detection Hlight: Oncoming vehicles with headlights on Taillgt: Preceding vehicles with taillights on Speed: Vehicle speed Daytime: Daytime state Village: Urban area Malfunc: System delay Delay: Standby Aim Lmt: Beam axis misaligned SAE Mod: Special detection Undefin: Undefined LIN Err: LIN malfunction
   Auto H Beam STS1	Automatic high beam sensor state past 1	Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err	Condition can be displayed	Although this item is displayed on the Techstream, it is not applicable to this vehicle.
   Auto H Beam STS2	Automatic high beam sensor state past 2	Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err	Condition can be displayed	Although this item is displayed on the Techstream, it is not applicable to this vehicle.
   Auto H Beam STS3	Automatic high beam sensor state past 3	Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err	Condition can be displayed	Although this item is displayed on the Techstream, it is not applicable to this vehicle.
   Auto H Beam STS4	Automatic high beam sensor state past 4	Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err	Condition can be displayed	Although this item is displayed on the Techstream, it is not applicable to this vehicle.
   Auto H Beam STS5	Automatic high beam sensor state past 5	Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err	Condition can be displayed	Although this item is displayed on the Techstream, it is not applicable to this vehicle.
   Auto H Beam STS6	Automatic high beam sensor state past 6	Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err	Condition can be displayed	Although this item is displayed on the Techstream, it is not applicable to this vehicle.
   Auto H Beam STS7	Automatic high beam sensor state past 7	Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err	Condition can be displayed	Although this item is displayed on the Techstream, it is not applicable to this vehicle.
   The Number of DTC	Number of trouble codes	0 to 255	Number of DTCs displayed	-
   *: If CAM NA is displayed, the forward recognition camera may have stopped operating due to high temperature.