Sliding Roof Does Not Move By Operating Sliding Roof Control Switch [12/2013 - ]: Procedure

1. Check the power window control system operates normally.

   for Models with Jam Protection Function on 4 Windows: Refer to OPERATION CHECK [12/2013 - ] .

   for Models with Jam Protection Function on Front Door Windows: Refer to OPERATION CHECK [12/2013 - ] .

   OK

   The power window control system operates normally.

   Proceed to
   OK
   NG

Result: 

NG 

GO TO POWER WINDOW CONTROL SYSTEM 

for Models with Jam Protection Function on 4 Windows: Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] .

for Models with Jam Protection Function on Front Door Windows: Refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2013 - ] .

Result: 

OK 

Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Sliding Roof / Data List.
5. Read the Data List according to the display on the Techstream.

   Body Electrical > Sliding Roof > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Open Switch	OPEN switch signal	OFF or ON	OFF: OPEN switch not pressed ON: OPEN switch pressed	-
   Close Switch	CLOSE switch signal	OFF or ON	OFF: CLOSE switch not pressed ON: CLOSE switch pressed	-
   Up Switch	UP switch signal	OFF or ON	OFF: UP switch not pressed ON: UP switch pressed	-
   Down Switch	DOWN switch signal	OFF or ON	OFF: DOWN switch not pressed ON: DOWN switch pressed	-

   Body Electrical > Sliding Roof > Data List 

   Tester Display
   Open Switch
   Close Switch
   Up Switch
   Down Switch

   OK

   The Techstream display changes according to switch operation as shown in the table.

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY): 

Refer to REMOVAL [12/2013 - ] .

Result: 

NG 

Go to next step 

1. Remove the sliding roof switch (map light assembly).

   Refer to REMOVAL [12/2013 - ] .

2. Inspect the sliding roof switch (map light assembly).

   Refer to INSPECTION [12/2013 - ] .

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE SLIDING ROOF SWITCH (MAP LIGHT ASSEMBLY): 

Refer to REMOVAL [12/2013 - ] .

Result: 

OK 

Go to next step 

1. Disconnect the S1 sliding roof switch (map light assembly) connector.
2. Disconnect the S5 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   S5-5 (CLS) - S1-16 (CLS)	Always	Below 1 Ω
   S5-5 (CLS) or S1-16 (CLS) - Body ground	Always	10 kΩ or higher
   S5-7 (OPN) - S1-17 (OPN)	Always	Below 1 Ω
   S5-7 (OPN) or S1-17 (OPN) - Body ground	Always	10 kΩ or higher
   S5-6 (DWN) - S1-5 (DOWN)	Always	Below 1 Ω
   S5-6 (DWN) or S1-5 (DOWN) - Body ground	Always	10 kΩ or higher
   S5-4 (UP) - S1-6 (UP)	Always	Below 1 Ω
   S5-4 (UP) or S1-6 (UP) - Body ground	Always	10 kΩ or higher
   S1-1 (GND) - Body ground	Always	Below 1 Ω
   S5-12 (E) - Body ground	Always	Below 1 Ω

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY): 

Refer to REMOVAL [12/2013 - ] .

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR