DTC P0741: Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL) [12/2012 - ]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

   Powertrain > Engine and ECT > Trouble Codes 

5. Read the DTCs using the Techstream.

   Result

   Result	Proceed to
   Only P0741 is output	A
   P0741 and other DTCs are output	B

   HINT: 

   If any other codes besides P0741 are output, perform the troubleshooting for those DTCs first.

Result: 

B 

GO TO DTC CHART:  DIAGNOSTIC TROUBLE CODE CHART [12/2012 - 11/2013]  ,  DIAGNOSTIC TROUBLE CODE CHART [11/2013 - 08/2014]  ,  DIAGNOSTIC TROUBLE CODE CHART [08/2014 - 10/2015]  ,  DIAGNOSTIC TROUBLE CODE CHART [10/2015 - 08/2016]  ,  DIAGNOSTIC TROUBLE CODE CHART [08/2016 - 08/2017]  ,  DIAGNOSTIC TROUBLE CODE CHART [08/2017 - ] 

Result: 

A 

See step  2

1. Remove the wiring harness connector.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Component without harness connected (Transmission Wire)

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   A-6 (SL) - Body ground	20°C (68°F)	11 to 15 Ω

Result: 

NG 

See step  6

Result: 

OK 

See step  3

1. Remove shift solenoid valve SL.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Shift Solenoid Valve SL

2. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

   OK

   Measurement Condition	Specified Condition
   Battery positive (+) → Shift solenoid valve SL connector Battery negative (-) → Shift solenoid valve SL body	Valve moves and makes an operating noise

Result: 

NG 

REPLACE SHIFT SOLENOID VALVE SL:  DISASSEMBLY [12/2012 - ] 

Result: 

OK 

See step  4

1. Check the transmission valve body assembly.

   Refer to DISASSEMBLY [12/2012 - ]

   OK

   There are no foreign objects on any valve.

Result: 

NG 

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY:  REMOVAL [12/2012 - ] 

Result: 

OK 

See step  5

1. Check the torque converter assembly.

   Refer to INSPECTION [12/2012 - ]

   OK

   The torque converter operates normally.

Result: 

OK 

REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY:  REMOVAL [12/2012 - 08/2017]  ,  REMOVAL [08/2017 - ] 

Result: 

NG 

REPLACE TORQUE CONVERTER ASSEMBLY:  REMOVAL [12/2012 - 08/2017]  ,  REMOVAL [08/2017 - ] 

1. Remove shift solenoid valve SL.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Shift Solenoid Valve SL

2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   Shift solenoid valve SL connector terminal - Shift solenoid valve SL body	20°C (68°F)	11 to 15 Ω

Result: 

OK 

REPLACE TRANSMISSION WIRE:  REMOVAL [12/2012 - ] 

Result: 

NG 

REPLACE SHIFT SOLENOID VALVE SL:  DISASSEMBLY [12/2012 - ]