LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2016 >> RAV4 SE, FWD >> Repair and Diagnosis >> Brakes >> Parking Brake System >> Parking Brake (Service Information) (Except Hybrid) >> Parking Brake Assembly >> Reassembly [12/2012 - ] >> Procedure

Reassembly [12/2012 - ]: Procedure

  1. APPLY HIGH TEMPERATURE GREASE 
    1. Apply a light coat of high-temperature grease to the areas of the backing plate that contact the shoes.
      GTY365538Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      High-temperature grease
  2. INSTALL PARKING BRAKE SHOE LEVER LH 
  3. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH 
    1. Connect the parking brake cable to the parking brake shoe lever.
    2. Apply a light coat of high-temperature grease to the following contact surfaces of the No. 2 parking brake shoe.
      GTY383374Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      High-temperature grease
      • Shoe to anchor pin
      • Shoe to parking brake lever pin
      • Shoe to spring
    3. Install the shoe with the shoe hold-down spring and shoe hold-down spring pin.
      GTY363105Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH 
    1. Apply a light coat of high-temperature grease to the following contact surfaces of the No. 1 parking brake shoe.
      GTY368691Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      High-temperature grease
      • Shoe to anchor pin
      • Shoe to spring
    2. Install the shoe with the shoe hold-down spring and shoe hold-down spring pin.
      GTY363104Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET 
    1. Apply a light coat of high-temperature grease to the areas of the shoe adjusting screw set shown in the illustration.
      GTY379127Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      High-temperature grease
    2. Install the shoe adjusting screw set.
  6. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side) 
    1. Using needle-nose pliers, install the shoe return tension spring.
  7. INSTALL PARKING BRAKE SHOE STRUT LH 
    1. Apply a light coat of high-temperature grease to the contact surface of the parking brake shoe strut and shoe return tension spring.
      GTY369260Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      High-temperature grease
    2. Install the parking brake shoe strut.
  8. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Upper Side) 
    1. Using needle-nose pliers, install the 2 shoe return tension springs.
      GTY363103Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. CHECK PARKING BRAKE INSTALLATION 
    1. Check that each part is installed properly.
      GTY378886Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A for LH Side *B for RH Side
      Front - -
      NOTE:

      There should be no oil or grease adhering to the friction surfaces of the shoe lining and disc.

  10. INSTALL REAR DISC 

    Refer to INSTALLATION [12/2012 - ]

  11. CHECK PARKING BRAKE LEVER TRAVEL 

    Refer to PROCEDURE - Step 1

  12. ADJUST PARKING BRAKE LEVER TRAVEL 

    Refer to PROCEDURE - Step 4

  13. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG 
  14. INSTALL REAR WHEEL 

    Torque: 103 N*m (1050 kgf*cm, 76 ft.*lbf) 

  15. SETTLE PARKING BRAKE SHOE AND DISC 
    1. Pull the parking brake lever with a force of 147 N (15 kgf, 33 lbf).
    2. Drive the vehicle at approximately 50 km/h (31 mph) for approximately 400 m (0.25 miles).
      NOTE:

      Drive the vehicle on a safe, level and dry road.

    3. Repeat the above steps 2 or 3 times.
scientia non olet · About LEMON Manuals