LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2016 >> RAV4 LE, AWD >> Repair and Diagnosis >> Drivelines & Axles >> Wheel Hubs >> Axle And Differential (Service Information) (Except Hybrid) >> Front Axle Hub >> Removal [12/2012 - ] >> Procedure

Removal [12/2012 - ]: Procedure

  1. REMOVE FRONT WHEEL 
  2. REMOVE FRONT AXLE SHAFT NUT LH 
    GTY158661Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using SST and a hammer, unstake the staked part of the front axle shaft nut.
      • SST: 09930-00010 
        1. 09931-00010
        2. 09931-00020
      NOTE:

      Loosen the staked part of the front axle shaft nut completely, otherwise the screw of the drive shaft may be damaged.

    2. While applying the brakes, remove the front axle shaft nut.
  3. DISCONNECT FRONT SPEED SENSOR LH 
    1. Remove the bolt and clamp, and disconnect the front speed sensor.
      NOTE:

      Be sure to disconnect the front speed sensor from the front shock absorber with coil spring completely.

      GTY365821Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt and disconnect the front speed sensor from the steering knuckle.
      NOTE:
      • Prevent foreign matter from attaching to the sensor tip.
      • Be careful not to damage the front speed sensor.
      • Clean the installation hole and the surface for the speed sensor every time the speed sensor is removed.
      GTY243623Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. DISCONNECT FRONT FLEXIBLE HOSE 
    1. Remove the bolt and disconnect the flexible hose.
      GTY376960Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. DISCONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH 
    1. Remove the 2 bolts and disconnect the front disc brake caliper assembly from the steering knuckle.
      NOTE:

      Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.

      GTY312131Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE FRONT DISC 

    Refer to PROCEDURE - Step 15

  7. DISCONNECT TIE ROD END SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 7

  8. DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 15

  9. REMOVE FRONT AXLE ASSEMBLY LH 
    1. Remove the 2 bolts and 2 nuts, and disconnect the front shock absorber assembly with coil spring from the steering knuckle.

      HINT: 

      While fixing the nuts in place, loosen and remove the bolts.

      GTY314642Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Put matchmarks on the drive shaft and front axle hub sub-assembly.
      GTY376360Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Matchmark
    3. Using a plastic-faced hammer, remove the steering knuckle assembly.
      NOTE:

      Be careful not to damage the front axle outboard joint boot and speed sensor rotor. Do not excessively push out the drive shaft from the axle assembly.

  10. REMOVE FRONT AXLE HUB SUB-ASSEMBLY LH 
    GTY312139Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Secure the front axle assembly in a vise.
      NOTE:

      When using a vise, do not overtighten it.

    2. Remove the 4 bolts and front axle hub sub-assembly from the steering knuckle.
      NOTE:

      Do not place the hub and bearing's magnet rotor side so that it is facing downward, and do not allow the magnet rotor side to become damaged or contact foreign matter.

    3. Remove the front brake dust cover from the steering knuckle.
scientia non olet · About LEMON Manuals