On-Vehicle Inspection [08/2015 - ]
- INSPECT COMBINATION METER SUB-ASSEMBLY
- LED INITIAL CHECK
- Check the illumination function of the warning or indicator lights listed below when turning the power switch on (IG).
OK
Warning or Indicator Specified Condition - Engine coolant temperature warning light
- Tire pressure warning light
- Headlight leveling warning light*4
- PCS OFF warning light*2, *5
- Hybrid system warning light*2
- Hybrid system overheat warning light*2
- Parking lock system warning light*2
- P position request indicator light*2
- LED headlight indicator light*2, *6
- Eco driving indicator light*2
- Maintenance required reminder indicator light*2, *3
- Master warning light*1
- Go to service warning light*2
Indicator or warning light comes on for about 3 seconds after turning the power switch on (IG). SRS warning light Warning light comes on for about 6 seconds after turning the power switch on (IG). - Oil pressure warning light
- Charge warning light
- EPS warning light
- MIL (Check engine warning light)
Warning light comes on when turning the power switch on (IG). - Brake warning light / red (malfunction)
- Slip indicator light
- ABS warning light
- Brake warning light / yellow (minor malfunction)
- TRAC OFF indicator light
- VSC OFF indicator light
- Indicator or warning light or indicator light comes on for about 3 seconds after turning the power switch on (IG).
- Indicator or warning light or indicator light comes on when turning the power switch from off to on (READY) for 3 seconds, then goes off.
- *1: w/ Multi-information display
- *2: w/o Multi-information display
- *3: for Speedometer with Imperial units for main scale
- *4: w/ Automatic headlight beam level control
- *5: w/ Pre-collision system
- *6: w/ LED headlights
- Check the illumination function of the warning or indicator lights listed below when turning the power switch on (IG).
- Check speedometer operation.NOTE:
- The combination meter sub-assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.
- The Data List values of the skid control ECU are used for this inspection. Therefore, make sure to perform the inspection after confirming that no DTCs are output from the brake control system.
- If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform the inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.
- Before starting the following inspection, check if the brake control system outputs the DTCs.
- Read the Data List according to the display on the Techstream.
ABS/VSC/TRAC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note Vehicle Speed Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) - REFERENCE: MPHTechstream Indication (mph) Acceptable Range (mph) 20 19.0 to 21.5 40 39.1 to 41.9 60 59.3 to 62.1 80 79.3 to 82.5 100 99.5 to 102.7 120 119.8 to 123 REFERENCE: KM/HTechstream Indication (km/h) Acceptable Range (km/h) 20 18.2 to 22.2 40 38.3 to 42.8 60 58.5 to 63.0 80 78.4 to 83.4 100 98.6 to 103.6 120 118.9 to 123.9 140 139.1 to 144.1 160 159.3 to 164.3 180 179.6 to 184.6
- LED INITIAL CHECK