LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2016 >> Highlander Limited, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 68 (Steering Column (Service Information) (Hybrid)) >> Steering Column Assembly >> Removal [02/2014 - ] >> Procedure

Removal [02/2014 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. PRECAUTION 

    Refer to PRECAUTION [02/2014 - ]

  2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD 
  3. REMOVE FRONT WHEEL LH 
  4. REMOVE HORN BUTTON ASSEMBLY 

    Refer to REMOVAL [02/2014 - ]

  5. REMOVE STEERING WHEEL ASSEMBLY 

    Refer to REMOVAL [02/2014 - ] 

  6. REMOVE LOWER STEERING COLUMN COVER 
    1. Remove the 2 screws.
      GTY450890Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 2 claws.
      GTY426050Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the claw and remove the lower steering column cover.
      GTY426051Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE UPPER STEERING COLUMN COVER 
    1. Disengage the 6 clips from the upper steering column cover.
      GTY425973Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 2 claws and remove the upper steering column cover.
      GTY425975Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY 
    NOTE:
    • Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).
    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly with the auxiliary battery connected and the power switch on (IG).
    • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.
    1. Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.
    2. Disengage the 3 claws to remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.
      GTY425974Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY 

    Refer to REMOVAL [02/2014 - ]

  10. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY 
    1. Loosen the bolt.
      GTY425970Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Put matchmarks on the steering intermediate shaft assembly and the steering link assembly.
      GTY442926Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Matchmark
    3. Remove the bolt and separate the steering intermediate shaft assembly from the steering link assembly.
  11. REMOVE NO. 4 AIR DUCT SUB-ASSEMBLY 
    1. Remove the bolt.
    2. Disengage the 2 claws and guide to remove the No. 4 air duct sub-assembly.
      GTY425972Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY 

    Refer to REMOVAL [02/2014 - ]

  13. REMOVE STEERING POST ASSEMBLY 
    1. Disconnect each connector and disengage each wire harness clamp from the steering post assembly.
    2. Remove the bolt to separate the ground wire.
      GTY425969Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the 2 clamps.
    4. Disconnect the 2 connectors.
    5. Remove the bolt, 2 nuts and steering post assembly.
      GTY450872Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals