LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2016 >> Highlander LE Plus, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 69 (Fuel System (2GR-FXS) - Service Information - (Hybrid)) >> Fuel Injector (For Port Injection) >> Removal [11/2016 - ] >> Procedure

Removal [11/2016 - ]: Procedure

WARNING: This page is about a different car, the 2019 Toyota Highlander, 2018 Toyota Highlander, and 2017 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. PRECAUTION 
    NOTE:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Refer to PRECAUTION [11/2016 - ]

  2. DISCHARGE FUEL SYSTEM PRESSURE 

    Refer to PRECAUTION [11/2016 - ]

  3. REMOVE DECK BOARD ASSEMBLY 

    Refer to PROCEDURE - Step 1

  4. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 2

  5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [11/2016 - ]

  6. REMOVE INTAKE AIR SURGE TANK ASSEMBLY 

    Refer to REMOVAL [11/2016 - ]

  7. DISCONNECT FUEL TUBE SUB-ASSEMBLY 
    1. Disconnect the fuel tube sub-assembly from the fuel delivery pipe with sensor assembly.
      GTY721746Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Refer to PRECAUTION [11/2016 - ]

  8. REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY 
    1. Disconnect the fuel pressure sensor connector.
      GTY721745Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the 2 No. 5 engine wire connectors.
      GTY721744Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 4 bolts and fuel delivery pipe with sensor assembly with the 6 fuel injector assemblies from the intake manifold.
      GTY738670Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe with sensor assembly.
      • When removing the fuel delivery pipe with sensor assembly, hold the pipe by both ends and pull it straight upward.
  9. REMOVE NO. 1 DELIVERY PIPE SPACER 
    1. Remove the 4 No. 1 delivery pipe spacers from the intake manifold.
      GTY657323Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE INJECTOR VIBRATION INSULATOR 
    1. Remove the 6 injector vibration insulators from the intake manifold.
      GTY657322Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE FUEL INJECTOR ASSEMBLY 
    1. for Bank 2:
      1. Disengage the clamp to disconnect the No. 5 engine wire from the fuel delivery pipe with sensor assembly.
        GTY684977Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Pull the 3 fuel injector assemblies out of the fuel delivery pipe with sensor assembly.
      3. Disconnect the 3 fuel injector assembly connectors.
        GTY669049Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. for Bank 1:
      1. Disengage the clamp to disconnect the No. 5 engine wire from the fuel delivery pipe with sensor assembly.
        GTY669048Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Pull the 3 fuel injector assemblies out of the fuel delivery pipe with sensor assembly.
      3. Disconnect the 3 fuel injector assembly connectors.
        GTY669046Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the O-ring from each fuel injector assembly.
    4. Attach a tag or label with the corresponding cylinder number to each fuel injector assembly so that they can be installed to their original locations.
      NOTE:

      Cover the fuel injector assemblies with plastic bags to prevent damage and contamination.

      GTY651227Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals