LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2016 >> Highlander LE Plus, AWD >> Repair and Diagnosis >> Restraints >> Seat Belts >> Seat Belts (Service Information) (Except Hybrid) >> Front Seat Outer Belt Assembly With Pre-TENSIONER >> Removal [12/2013 - ] >> Procedure

Removal [12/2013 - ]: Procedure

  1. PRECAUTION 
    NOTE:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Refer to PRECAUTION [12/2013 - 11/2016] , or refer to PRECAUTION [11/2016 - ]

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    WARNING:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [12/2013 - 11/2016] , or refer to INITIALIZATION [11/2016 - ]

  3. REMOVE FRONT DOOR SCUFF PLATE 

    Refer to PROCEDURE - Step 7 , or refer to PROCEDURE - Step 7 , or refer to PROCEDURE - Step 7

  4. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP 
    1. Disconnect the front door opening trim weatherstrip.
  5. REMOVE REAR OUTER SEAT TRACK BRACKET COVER 

    Refer to PROCEDURE - Step 4

  6. REMOVE REAR DOOR SCUFF PLATE 

    Refer to PROCEDURE - Step 12 , or refer to PROCEDURE - Step 12 , or refer to PROCEDURE - Step 12

  7. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP 
    1. Disconnect the rear door opening trim weatherstrip.
  8. REMOVE LOWER CENTER PILLAR GARNISH 

    Refer to PROCEDURE - Step 14 , or refer to PROCEDURE - Step 14 , or refer to PROCEDURE - Step 14

  9. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY 
    1. Remove the bolt to disconnect the floor anchor of the front seat outer belt assembly.
      GTY427255Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE CENTER PILLAR GARNISH 

    Refer to PROCEDURE - Step 16 , or refer to PROCEDURE - Step 16 , or refer to PROCEDURE - Step 16

  11. REMOVE FRONT SEAT OUTER BELT ASSEMBLY 
    1. Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly.
      GTY427257Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. for LH Side:
      1. Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector as shown in the illustration.

        HINT: 

        Tape the screwdriver tip before use.

        GTY442630Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Protective Tape
        *b Locking Button
        *c Release
    3. for RH Side:
      1. Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector as shown in the illustration.

        HINT: 

        Tape the screwdriver tip before use.

        GTY451999Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Protective Tape
        *b Locking Button
        *c Release
        *d Pretensioner Connector
        *e Selectable Force Limiter Connector
      2. Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the selectable force limiter connector as shown in the illustration.

        HINT: 

        Tape the screwdriver tip before use.

    4. Remove the 2 bolts and front seat outer belt assembly.
      GTY427287Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY 
    1. Remove the 2 bolts.
      GTY427288Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the guide to remove the front shoulder belt anchor adjuster assembly.
scientia non olet · About LEMON Manuals