TC and CG Terminal Circuit [11/2016 - ]: Procedure
- CHECK CAN COMMUNICATION SYSTEM
- Check for DTCs.
Refer to DIAGNOSIS SYSTEM [11/2016 - ]
Result Proceed to DTCs are not output. A DTCs are output. B
Result:
B
GO TO CAN COMMUNICATION SYSTEM.
Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2016 - ]
Result:
A
See step 2
- Check for DTCs.
- CHECK DTC (C2179/79)
- Check if DTC C2179/79 is output.
Refer to DTC CHECK / CLEAR [02/2014 - ]
Result Proceed to DTC C2179/79 is not output. A DTC C2179/79 is output. B
Result:
B
GO TO DTC C2179/79.
Refer to DTC C2179/79: Tire Pressure Monitor ECU Communication Stop [02/2014 - ]
Result:
A
See step 3
- Check if DTC C2179/79 is output.
- INSPECT DLC3
- Turn the power switch on (IG).
*a Front view of DLC3 - Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection Condition Specified Condition F25-13 (TC) - F25-4 (CG) Power switch on (IG) 11 to 14 V Proceed to OK NG
Result:
NG
See step 5
Result:
OK
See step 4
- Turn the power switch on (IG).
- REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY
- Turn the power switch off.
*a Front view of DLC3 - Replace the hybrid vehicle control ECU assembly.
Refer to REMOVAL [11/2016 - ]
- Using SST, connect terminals TC and CG of the DLC3.
- SST: 09843-18040
- Check that the tire pressure warning light is blinking.
OK
The tire pressure warning light is blinking.
HINT:
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.
Refer to PROBLEM SYMPTOMS TABLE [02/2014 - ]
Proceed to OK NG
Result:
OK
END
Result:
NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE.
Refer to PROBLEM SYMPTOMS TABLE [02/2014 - ]
- Turn the power switch off.
- CHECK HARNESS AND CONNECTOR (TC of DLC3 - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
- Disconnect the F137 hybrid vehicle control ECU assembly connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition F25-13 (TC) - F137-28 (TC) Always Below 1 Ω F25-13 (TC) or F137-28 (TC) - Body ground Always 10 kΩ or higher Proceed to OK NG
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
OK
See step 6
- CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
- Measure the resistance according to the value(s) in the table below.
*a Front view of DLC3 Standard Resistance
Tester Connection Condition Specified Condition F25-4 (CG) - Body ground Always Below 1 Ω HINT:
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.
Refer to PROBLEM SYMPTOMS TABLE [02/2014 - ]
Proceed to OK NG
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
OK
See step 7
- Measure the resistance according to the value(s) in the table below.
- REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY
- Replace the power management control ECU.
*a Front view of DLC3 Refer to REMOVAL [11/2016 - ]
- Using SST, connect terminals TC and CG of the DLC3.
- SST: 09843-18040
- Check that the tire pressure warning light is blinking.
OK
The tire pressure warning light is blinking.
HINT:
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.
Refer to PROBLEM SYMPTOMS TABLE [02/2014 - ]
Proceed to OK NG
Result:
OK
END
Result:
NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE.
Refer to PROBLEM SYMPTOMS TABLE [02/2014 - ]
- Replace the power management control ECU.