DTC B1423/23: Pressure Sensor Circuit [11/2016 - ]: Procedure

1. Disconnect the A13 air conditioner tube and accessory assembly connector.
2. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   A13-3 (+) - Body ground	Power switch on (IG)	4.75 to 5.25 V

   Result

   Proceed to
   OK
   NG

Result:  2

NG 

See step  18

Result:  1

OK 

See step  2

1. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   A13-1 (-) - Body ground	Always	Below 1 Ω

   Result

   Proceed to
   OK
   NG

Result:  2

NG 

See step  17

Result:  1

OK 

See step  3

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Connect the A13 air conditioner tube and accessory assembly connector.
2. Remove the air conditioning amplifier assembly with the connectors still connected.
3. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   F80-9 (PRE) - Body ground	Power switch on (IG) (A/C switch: Off)	0.74 to 4.71 V

   HINT: 

   If the voltage is not as specified, there may be a malfunction in the air conditioning amplifier assembly, air conditioner tube and accessory assembly, or wire harness. It is also possible that the amount of refrigerant may not be appropriate.

   Result

   Proceed to
   OK
   NG

Result:  2

NG 

See step  11

Result:  1

OK 

See step  4

1. Measure the voltage when the following conditions are met.
   MEASUREMENT CONDITION:
   
   

   Item	Condition
   Vehicle doors	Fully open
   Temperature setting	MAX COLD
   Blower speed	HI
   A/C switch	On
   Recirculation/fresh switch	RECIRCULATION
   Interior temperature	25 to 35°C (77 to 95°F)

   NOTE:

   • If refrigerant pressure on the high pressure side becomes extremely high during the inspection (if the voltage exceeds 4.71 V), the fail-safe function stops compressor operation. Therefore, measure the voltage before the fail-safe operation.
   • It is necessary to measure the voltage for a certain amount of time (approximately 10 minutes) because the malfunction may recur after a while.

   HINT: 

   When the outside air temperature is low (below -1.5°C (29.3°F)), the compressor stops due to operation of the thermistor assembly and the No. 1 cooler thermistor to prevent the evaporator from freezing. In this case, perform the inspection in a warm indoor environment.

   1. Measure the voltage according to the value(s) in the table below.

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      *a	Component with harness connected (Air Conditioning Amplifier Assembly)

      Standard Voltage

      Tester Connection	Condition	Specified Condition
      F80-9 (PRE) - Body ground	Power switch on (IG) (A/C switch: On)	0.74 to 4.71 V

   Result

   Result	Proceed to
   OK (When troubleshooting according to DTC)	A
   OK (When troubleshooting according to Problem Symptoms Table)	B
   NG	C

Result:  1

A 

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY. Refer to  REMOVAL [02/2014 - ] 

Result:  2

B 

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [11/2016 - ] 

Result:  3

C 

See step  5

1. Check if the cooling fan operates normally.

   Refer to ON-VEHICLE INSPECTION [11/2016 - ]

   Result

   Proceed to
   OK
   NG

Result:  2

NG 

GO TO COOLING FAN SYSTEM. Refer to  ON-VEHICLE INSPECTION [11/2016 - ] 

Result:  1

OK 

See step  6

1. Use a refrigerant recovery unit to recover refrigerant.
2. Evacuate the air conditioning system.
3. Add an appropriate amount of refrigerant.

   Refer to REPLACEMENT [02/2014 - ]

   HINT: 

   If refrigerant is added and the system has not been properly evacuated (insufficient vacuum time), moisture in the air remaining in the system will freeze in the cooler expansion valve, blocking the flow on the high pressure side. Therefore, in order to confirm the problem, recover the refrigerant and properly evacuate the system. Add an appropriate amount of refrigerant, and check for the DTC.

Result: 

NEXT 

1. Recheck for DTCs when the following conditions are met.
   MEASUREMENT CONDITION:
   
   

   Item	Condition
   Vehicle doors	Fully open
   Temperature setting	MAX COLD
   Blower speed	HI
   A/C switch	On
   Recirculation/fresh switch	RECIRCULATION
   Interior temperature	25 to 35°C (77 to 95°F)

   Body Electrical > Air Conditioner > Trouble Codes 

   NOTE:

   If refrigerant pressure on the high pressure side becomes high, the DTC will be stored. It is necessary to operate the air conditioning system for a certain amount of time (approximately 10 minutes) because the DTC may be stored after the air conditioning operates for a while.

   HINT: 

   • When the outside air temperature is low (below -1.5°C (29.3°F)), the compressor stops due to operation of the thermistor assembly and the No. 1 cooler thermistor to prevent the evaporator from freezing. In this case, perform the inspection in a warm indoor environment.
   • If refrigerant is added and the system has not been properly evacuated (insufficient vacuum time), moisture in the air remaining in the system will freeze in the cooler expansion valve, blocking the flow on the high pressure side. Therefore, in order to confirm the problem, recover the refrigerant and properly evacuate the system. Add an appropriate amount of refrigerant, and check for the DTC. If the DTC is not output after this work, it indicates that the cooler dryer in the cooler condenser assembly is not able to absorb moisture in the refrigerant cycle. It is necessary to replace the cooler dryer in order to complete the repair.

   Result

   Result	Proceed to
   DTC B1423/23 is not output	A
   DTC B1423/23 is output	B

Result:  1

A 

REPLACE COOLER CONDENSER ASSEMBLY. Refer to  REMOVAL [11/2016 - ] 

Result:  2

B 

See step  8

1. Replace the cooler expansion valve with a new or known good one.

   Refer to REMOVAL [02/2014 - ]

   HINT: 

   Replace the cooler expansion valve with a new or known good one because the cooler expansion valve is either stuck or clogged.

Result: 

NEXT 

1. Use a refrigerant recovery unit to recover refrigerant.
2. Evacuate the air conditioning system.
3. Add an appropriate amount of refrigerant.

   Refer to REPLACEMENT [02/2014 - ]

   HINT: 

   If refrigerant is added and the system has not been properly evacuated (insufficient vacuum time), moisture in the air remaining in the system will freeze in the cooler expansion valve, blocking the flow on the high pressure side. Therefore, in order to confirm the problem, recover the refrigerant and properly evacuate the system. Add an appropriate amount of refrigerant, and check for the DTC.

Result: 

NEXT 

1. Recheck for DTCs when the following conditions are met.
   MEASUREMENT CONDITION:
   
   

   Item	Condition
   Vehicle doors	Fully open
   Temperature setting	MAX COLD
   Blower speed	HI
   A/C switch	On
   Recirculation/fresh switch	RECIRCULATION
   Interior temperature	25 to 35°C (77 to 95°F)

   Body Electrical > Air Conditioner > Trouble Codes 

   NOTE:

   If refrigerant pressure on the high pressure side becomes high, the DTC will be stored. It is necessary to operate the air conditioning system for a certain amount of time (approximately 10 minutes) because the DTC may be stored after the air conditioning operates for a while.

   HINT: 

   • When the outside air temperature is low (below -1.5°C (29.3°F)), the compressor stops due to operation of the thermistor assembly and the No. 1 cooler thermistor to prevent the evaporator from freezing. In this case, perform the inspection in a warm indoor environment.
   • If refrigerant pressure is not normal after replacing the cooler expansion valve with a new or known good one, the cooler condenser assembly or pipes may be clogged due to dirt, dust or other foreign matter. In this case, clean or replace the cooler condenser assembly or pipes.

   Result

   Result	Proceed to
   DTC B1423/23 is not output	A
   DTC B1423/23 is output	B

Result:  1

A 

END 

Result:  2

B 

CLEAN OR REPLACE COOLER CONDENSER ASSEMBLY OR PIPE 

1. Disconnect the A13 air conditioner tube and accessory assembly connector.
2. Disconnect the F80 air conditioning amplifier assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   A13-2 (PR) - F80-9 (PRE)	Always	Below 1 Ω
   A13-2 (PR) or F80-9 (PRE) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result:  2

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result:  1

OK 

See step  12

1. Install a manifold gauge set.
2. Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.
3. Evacuate the air conditioning system and check that vacuum can be maintained.

   OK

   Vacuum can be maintained in the air conditioning system.

   HINT: 

   If vacuum cannot be maintained in the air conditioning system, refrigerant may be leaking from it. In this case, it is necessary to repair or replace the leaking part of the air conditioning system.

   Result

   Proceed to
   OK
   NG

Result:  3

NG 

See step  16

Result:  1

OK 

See step  13

1. Use a refrigerant recovery unit to recover refrigerant.
2. Evacuate the air conditioning system.
3. Add an appropriate amount of refrigerant.

   Refer to REPLACEMENT [02/2014 - ]

   HINT: 

   If refrigerant is added and the system has not been properly evacuated (insufficient vacuum time), moisture in the air remaining in the system will freeze in the cooler expansion valve, blocking the flow on the high pressure side. Therefore, in order to confirm the problem, recover the refrigerant and properly evacuate the system. Add an appropriate amount of refrigerant, and check for the DTC.

Result: 

NEXT 

1. Recheck for DTCs when the following conditions are met.
   MEASUREMENT CONDITION:
   
   

   Item	Condition
   Vehicle doors	Fully open
   Temperature setting	MAX COLD
   Blower speed	HI
   A/C switch	On
   Recirculation/fresh switch	RECIRCULATION
   Interior temperature	25 to 35°C (77 to 95°F)

   Body Electrical > Air Conditioner > Trouble Codes 

   NOTE:

   If refrigerant pressure on the high pressure side becomes high, the DTC will be stored. It is necessary to operate the air conditioning system for a certain amount of time (approximately 10 minutes) because the DTC may be stored after the air conditioning operates for a while.

   HINT: 

   When the outside air temperature is low (below -1.5°C (29.3°F)), the compressor stops due to operation of the thermistor assembly and the No. 1 cooler thermistor to prevent the evaporator from freezing. In this case, perform the inspection in a warm indoor environment.

   Result

   Result	Proceed to
   DTC B1423/23 is not output	A
   DTC B1423/23 is output	B

   NOTE:

   If the DTC was stored due to an insufficient or excessive amount of refrigerant, the problem may have been solved after performing the previous step. However, the root cause of insufficient refrigerant may be refrigerant leaks. The root cause of excessive refrigerant may be adding too much refrigerant when the level was insufficient. Therefore, identify and repair the area where refrigerant leaks from as necessary.

Result:  1

A 

END 

Result:  2

B 

See step  15

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install a manifold gauge set.
2. Connect the A13 air conditioner tube and accessory assembly connector.
3. Turn the power switch on (IG).
4. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   F80-9 (PRE) - F80-13 (SG-2)	Refrigerant pressure: Normal pressure (less than 3025 kPa (30.8 kgf/cm2 , 439 psi) and more than 176 kPa (1.8 kgf/cm2 , 26 psi))	0.74 to 4.71 V

   Result

   Proceed to
   OK
   NG

Result:  1

OK 

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY. Refer to  REMOVAL [02/2014 - ] 

Result:  2

NG 

REPLACE AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY 

1. Identify the area where refrigerant leaks from.

   Refer to REPLACEMENT [02/2014 - ]

2. Repair the identified area of the air conditioning system.
3. Evacuate the air conditioning system.

Result: 

NEXT 

CHARGE SYSTEM WITH REFRIGERANT. Refer to  REPLACEMENT [02/2014 - ] 

1. Disconnect the F80 air conditioning amplifier assembly connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   A13-1 (-) - F80-13 (SG-2)	Always	Below 1 Ω
   A13-1 (-) or F80-13 (SG-2) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result:  1

OK 

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY. Refer to  REMOVAL [02/2014 - ] 

Result:  2

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

1. Disconnect the F80 air conditioning amplifier assembly connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   A13-3 (+) - F80-10 (S5-3)	Always	Below 1 Ω
   A13-3 (+) or F80-10 (S5-3) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result:  1

OK 

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY. Refer to  REMOVAL [02/2014 - ] 

Result:  2

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR