LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2016 >> Highlander Hybrid Limited >> Repair and Diagnosis >> External Pages >> Different car >> Section 78 (Hybrid Control System (2GR-FXS) - Diagnostic Codes (6 Of 6)) >> Hybrid Control System >> DTC P0A45-669: Drive Motor "B" Position Sensor Circuit [11/2016 - ] >> Procedure

DTC P0A45-669: Drive Motor "B" Position Sensor Circuit [11/2016 - ]: Procedure

WARNING: This page is about a different car, the 2019 Toyota Highlander, 2018 Toyota Highlander, and 2017 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR) 

    Refer to PROCEDURE - Step 3

    Result

    Result Proceed to
    OK A
    NG (The connector is not connected securely.) B
    NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C

    Result:  2

    B 

    CONNECT SECURELY 

    Result:  3

    C 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result:  1

    A 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - REAR MOTOR RESOLVER) 

    Refer to PROCEDURE - Step 7 Refer to PROCEDURE - Step 7

    Result

    Proceed to
    OK
    NG

    Result:  2

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result:  1

    OK 

    See step  3

  3. CHECK REAR MOTOR RESOLVER 

    Refer to PROCEDURE - Step 8 Refer to PROCEDURE - Step 8

    Result

    Proceed to
    OK
    NG

    Result:  2

    NG 

    See step  5

    Result:  1

    OK 

    See step  4

  4. CHECK CONNECTOR CONNECTION CONDITION (REAR MOTOR RESOLVER CONNECTOR) 

    Refer to PROCEDURE - Step 11 Refer to PROCEDURE - Step 12

    Result

    Result Proceed to
    OK A
    NG (The connector is not connected securely.) B
    NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C

    Result:  1

    A 

    REPLACE INVERTER WITH CONVERTER ASSEMBLY. Refer to  COMPONENTS [11/2016 - ] 

    Result:  2

    B 

    CONNECT SECURELY 

    Result:  3

    C 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  5. CHECK CONNECTOR CONNECTION CONDITION (REAR MOTOR RESOLVER CONNECTOR) 

    Refer to PROCEDURE - Step 12 Refer to PROCEDURE - Step 12

    Result

    Result Proceed to
    OK A
    NG (The connector is not connected securely.) B
    NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C

    Result:  2

    B 

    CONNECT SECURELY 

    Result:  3

    C 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result:  1

    A 

    See step  6

  6. INSPECT REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY (REAR MOTOR RESOLVER) 

    Refer to PROCEDURE - Step 13 Refer to PROCEDURE - Step 13

    Result

    Proceed to
    OK
    NG

    Result:  1

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result:  2

    NG 

    REPLACE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY. Refer to  COMPONENTS [11/2016 - ] 

scientia non olet · About LEMON Manuals