LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2016 >> Highlander Hybrid Limited >> Repair and Diagnosis >> External Pages >> Different car >> Section 76 (Hybrid Control System (2GR-FXS) - Diagnostic Codes (2 Of 6)) >> Hybrid Control System >> DTC P0705-758: Transmission Range Sensor Circuit [11/2016 - ] >> Procedure

DTC P0705-758: Transmission Range Sensor Circuit [11/2016 - ]: Procedure

WARNING: This page is about a different car, the 2019 Toyota Highlander, 2018 Toyota Highlander, and 2017 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK DTC OUTPUT (HYBRID CONTROL) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
    4. Check for DTCs.

      Powertrain > Hybrid Control > Trouble Codes 

      Result

      Result Proceed to
      P0705-758 only is output. A
      P0705-757 is also output. B
    5. Turn the power switch off.

    Result:  2

    B 

    GO TO DTC CHART (P0705-757). Refer to  DTC P0705-757: Transmission Range Sensor Circuit [11/2016 - ]  

    Result:  1

    A 

    See step  2

  2. CHECK SHIFT LEVER POSITION SENSOR 
    1. Turn the power switch on (IG).
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      A86-34 (MJ) - Body ground Power switch on (IG)
      Shift lever in P, R, N, D or S      		 11 to 14 V
      GTY707454Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Hybrid Vehicle Control ECU Assembly)
    3. Turn the power switch off.

      Result

      Proceed to
      OK
      NG

    Result:  2

    NG 

    See step  4

    Result:  1

    OK 

    See step  3

  3. CHECK FOR INTERMITTENT PROBLEMS 

    Refer to CHECK FOR INTERMITTENT PROBLEMS [02/2014 - ]

    Result

    Proceed to
    OK
    NG

    Result:  1

    OK 

    REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY. Refer to  COMPONENTS [11/2016 - ] 

    Result:  2

    NG 

    REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA 

  4. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT) 

    See step  4

    Result

    Proceed to
    OK
    NG

    Result:  2

    NG 

    See step  6

    Result:  1

    OK 

    See step  5

  5. INSPECT SHIFT LEVER POSITION SENSOR 
    1. Disconnect the C15 shift lever position sensor connector.
    2. Measure the resistance according to the value(s) in the table below.
      GTY454048Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Shift Lever Position Sensor)

      Standard Resistance

      Tester Connection Condition Specified Condition
      8 (+B) - 5 (MJ) Shift lever in P, R, N, D or S Below 1 Ω
    3. Reconnect the C15 shift lever position sensor connector.

      Result

      Proceed to
      OK
      NG

    Result:  1

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result:  2

    NG 

    REPLACE SHIFT LEVER POSITION SENSOR. Refer to  COMPONENTS [02/2014 - ] 

  6. CHECK HARNESS AND CONNECTOR (SHIFT LEVER POSITION SENSOR - HYBRID VEHICLE CONTROL ECU ASSEMBLY) 

    See step  6

    Result

    Proceed to
    OK
    NG

    Result:  1

    OK 

    REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY. Refer to  COMPONENTS [11/2016 - ] 

    Result:  2

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals