LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2016 >> Highlander Hybrid Limited >> Repair and Diagnosis >> External Pages >> Different car >> Section 75 (Hybrid Control System (2GR-FXS) - Diagnostic Codes (3 Of 6)) >> Hybrid Control System >> DTC P324E-788: MG-ECU Power Relay Intermittent Circuit [11/2016 - ] >> Procedure

DTC P324E-788: MG-ECU Power Relay Intermittent Circuit [11/2016 - ]: Procedure

WARNING: This page is about a different car, the 2019 Toyota Highlander, 2018 Toyota Highlander, and 2017 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK DTC OUTPUT (HYBRID CONTROL) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
    4. Check for DTCs.

      Powertrain > Hybrid Control > Trouble Codes 

      Result

      Result Proceed to
      P324E-788 only is output or any DTCs other than U0110-159, 160, 656, 657 is also output. A
      U0110-159, 160, 656, 657 are also output. B
    5. Turn the power switch off.

    Result:  2

    B 

    GO TO DTC CHART (HYBRID CONTROL SYSTEM). Refer to  DIAGNOSTIC TROUBLE CODE CHART [11/2016 - 10/2017]  Refer to  DIAGNOSTIC TROUBLE CODE CHART [10/2017 - ] 

    Result:  1

    A 

    See step  2

  2. CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR) 

    Refer to PROCEDURE - Step 3

    Result

    Result Proceed to
    OK A
    NG (The connector is not connected securely.) B
    NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C

    Result:  2

    B 

    CONNECT SECURELY 

    Result:  3

    C 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result:  1

    A 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - IGCT RELAY) 
    WARNING:

    Be sure to wear insulated gloves.

    1. Check that the service plug grip is not installed.
      NOTE:

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair information because this may cause a malfunction.

    2. Disconnect the A46 inverter with converter assembly connector.
    3. Remove the IGCT relay from the No. 3 engine room relay block.
    4. Measure the resistance according to the value(s) in the table below.
      GTY451600Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 No. 3 Engine Room Relay Block *2 IGCT Relay
      *a Front view of wire harness connector
      (to Inverter with Converter Assembly)      		 - -

      Standard Resistance

      Tester Connection Condition Specified Condition
      A46-30 (+B) - 5 (IGCT relay) Power switch off Below 1 Ω
      A46-31 (+B2) - 5 (IGCT relay) Power switch off Below 1 Ω
      A46-10 (GND1) - Body ground Power switch off Below 1 Ω
      A46-11 (GND2) - Body ground Power switch off Below 1 Ω
    5. Install the IGCT relay.
    6. Reconnect the A46 inverter with converter assembly connector.

      Result

      Proceed to
      OK
      NG

    Result:  1

    OK 

    REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS. Refer to  DTC CHECK / CLEAR [11/2016 - ] 

    Result:  2

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals