LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2016 >> Highlander Hybrid Limited >> Repair and Diagnosis >> External Pages >> Different car >> Section 74 (Power Switch (2GR-FXS) - Service Information - (Hybrid)) >> Power Switch >> Installation [11/2016 - ] >> Procedure

Installation [11/2016 - ]: Procedure

WARNING: This page is about a different car, the 2019 Toyota Highlander, 2018 Toyota Highlander, and 2017 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL POWER SWITCH 
    1. Engage the 2 claws to install the power switch to the No. 1 switch hole base.
  2. INSTALL NO. 1 SWITCH HOLE BASE 

    Refer to PROCEDURE - Step 4

  3. INSTALL INSTRUMENT PANEL FINISH PLATE 

    Refer to PROCEDURE - Step 6

  4. INSTALL INSTRUMENT CLUSTER FINISH PANEL END 

    Refer to PROCEDURE - Step 7

  5. INSTALL INSTRUMENT CLUSTER FINISH PANEL ORNAMENT 

    Refer to PROCEDURE - Step 8

  6. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 9

  7. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 10

  8. INSTALL INSTRUMENT PANEL FINISH PANEL END RH 

    Refer to PROCEDURE - Step 11

  9. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH 

    Refer to PROCEDURE - Step 63

  10. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH 

    Refer to PROCEDURE - Step 64

  11. INSTALL FRONT DOOR SCUFF PLATE RH 

    Refer to PROCEDURE - Step 65

  12. INSTALL CONSOLE BOX INSERT 

    Refer to PROCEDURE - Step 18

  13. INSTALL FRONT NO. 2 CONSOLE BOX INSERT 

    Refer to PROCEDURE - Step 19

  14. INSTALL NO. 2 SWITCH HOLE BASE 

    Refer to PROCEDURE - Step 20

  15. INSTALL CONSOLE BOX ASSEMBLY 

    Refer to INSTALLATION [02/2014 - ]

  16. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL WITH AIR CONDITIONING CONTROL ASSEMBLY 

    Refer to PROCEDURE - Step 28

  17. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 32

  18. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 33

  19. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 34

  20. INSTALL INSTRUMENT PANEL FINISH PANEL END LH 

    Refer to PROCEDURE - Step 35

  21. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 53

  22. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 54

  23. INSTALL FRONT DOOR SCUFF PLATE LH 

    Refer to PROCEDURE - Step 55

  24. INSTALL COMBINATION METER ASSEMBLY 

    Refer to INSTALLATION [02/2014 - ]

  25. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [11/2016 - ]

  26. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 70

  27. INSTALL DECK BOARD ASSEMBLY 

    Refer to PROCEDURE - Step 71

scientia non olet · About LEMON Manuals