Speedometer Malfunction [02/2014 - ]: Procedure

1. Check if CAN communication DTCs are output.

   Refer to DIAGNOSIS SYSTEM [02/2014 - 11/2016] .

   Refer to DIAGNOSIS SYSTEM [11/2016 - ] .

   Result	Proceed to
   CAN communication DTCs are not output.	A
   CAN communication DTCs are output.	B

Result: 

B 

GO TO CAN COMMUNICATION SYSTEM: 

Refer to HOW TO PROCEED WITH TROUBLESHOOTING [02/2014 - 11/2016] .

Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2016 - ] .

Result: 

A 

Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Combination Meter / Active Test.
5. Check the operation by referring to the table below.

   Body Electrical > Combination Meter > Active Test 

   Tester Display	Measurement Item	Control Range	Diagnostic Note
   Speed Meter Operation	Speedometer	OFF, 0, 40, 80, 120 mph*1 OFF, 0, 40, 80, 120, 160, 200 km/h*2	There is a deviation in the values displayed on the speedometer (Control range → Speedometer display) Reference mph*1:  40 → 39.7 to 42.5 80 → 80.6 to 83.8 120 → 121.7 to 124.9 Reference km/h*2:  40 → 38.9 to 43.4 80 → 79.7 to 84.7 120 → 120.8 to 125.8 160 → 161.9 to 166.9 200 → 203.0 to 208.0
   *1: for Speedometer with Imperial Units for Main Scale *2: for Speedometer with Metric Units for Main Scale

   Body Electrical > Combination Meter > Active Test 

   Tester Display
   Speed Meter Operation

   OK

   Speedometer indication is normal.

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE COMBINATION METER ASSEMBLY: 

Refer to REMOVAL [02/2014 - ] .

Result: 

OK 

Go to next step 

1. Check if electronically controlled brake system DTCs are output.

   Refer to DTC CHECK / CLEAR [02/2014 - ] .

   Chassis > ABS/VSC/TRAC > Trouble Codes 

   Result	Proceed to
   Electronically controlled brake system DTCs are not output.	A
   Electronically controlled brake system DTCs are output.	B

Result: 

B 

GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM: 

Refer to HOW TO PROCEED WITH TROUBLESHOOTING [02/2014 - ] .

Result: 

A 

Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus:
   1. for ABS/VSC/TRAC: Chassis / ABS/VSC/TRAC / Data List.
   2. for Combination Meter: Body Electrical / Combination Meter / Data List.
5. Check the values by referring to the table below.

   Chassis > ABS/VSC/TRAC > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Vehicle Speed	Maximum wheel speed sensor	Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)	Vehicle stopped: 0 km/h (0 mph)	When driving at constant speed: No large fluctuations

   Chassis > ABS/VSC/TRAC > Data List 

   Tester Display
   Vehicle Speed

   Body Electrical > Combination Meter > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Vehicle Speed Meter	Vehicle speed	Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)	Almost the same as actual vehicle speed	-

   Body Electrical > Combination Meter > Data List 

   Tester Display
   Vehicle Speed Meter

   Result	Proceed to
   The data list values of the ECUs match.	A
   The data list values of the ECUs do not match.	B

   HINT: 

   • When the data list values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.
   • When the data list values of the ECUs do not match, a signal output error of the skid control ECU assembly or an internal malfunction of the combination meter assembly is suspected.

Result: 

A 

REPLACE COMBINATION METER ASSEMBLY: 

Refer to REMOVAL [02/2014 - ] .

Result: 

B 

Go to next step 

1. Replace the combination meter assembly with a new or known good one.

   Refer to REMOVAL [02/2014 - ] .

   OK

   The operation of the speedometer returns to normal.

   Proceed to
   OK
   NG

Result: 

OK 

END 

Result: 

NG 

REPLACE SKID CONTROL ECU ASSEMBLY: 

Refer to REMOVAL [02/2014 - ] .