How To Proceed With Troubleshooting [02/2014 - ]: Procedure
- VEHICLE BROUGHT TO WORKSHOP
Result:
NEXT
See step 2
- CUSTOMER PROBLEM ANALYSIS
- When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
- Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
- The following 5 items are important points for problem analysis:
What Vehicle model, system name When Date, time, occurrence frequency Where Road conditions Under what conditions? Driving conditions, weather conditions How did it happen? Problem symptoms
Result:
NEXT
See step 3
- INSPECT AUXILIARY BATTERY
- Measure the auxiliary battery voltage with the power switch off.
Standard Voltage
11 to 14 V
HINT:
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
Result:
NEXT
See step 4
- Measure the auxiliary battery voltage with the power switch off.
- CHECK CABIN
- Check that condensation is not likely to occur in the cabin and that the temperature is not high or extremely low in the cabin.
OK
Condensation is not likely being produced and the temperature is not high or extremely low.
HINT:
- A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.
- The rear seat entertainment system may not operate normally when the temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher.
Result:
NG
SET CABIN TO APPROPRIATE TEMPERATURE
Result:
OK
See step 5
- Check that condensation is not likely to occur in the cabin and that the temperature is not high or extremely low in the cabin.
- CHECK FOR DTC*
- Refer to DTC Check / Clear.
Refer to DTC CHECK / CLEAR [02/2014 - ]
Result Proceed to DTCs are output. A DTCs are not output. B HINT:
If the system cannot enter diagnostic mode, inspect the AVC-LAN and all the components that connect to the AVC-LAN for short circuits and repair or replace the problem part.
Refer to AVC-LAN Circuit [02/2014 - ]
Result:
B
See step 8
Result:
A
See step 6
- Refer to DTC Check / Clear.
- DTC CLEAR*
- Refer to DTC Check / Clear.
Refer to DTC CHECK / CLEAR [02/2014 - ]
HINT:
The present DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.
Result:
NEXT
See step 7
- Refer to DTC Check / Clear.
- RECHECK FOR DTC*
- Refer to DTC Check / Clear.
Refer to DTC CHECK / CLEAR [02/2014 - ]
Result Proceed to DTCs are not output. A DTCs are output. B HINT:
- Even if the problem symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.
- If the system cannot enter diagnostic mode, inspect the AVC-LAN and all the components that connect to the AVC-LAN for short circuits and repair or replace the problem part.
Refer to AVC-LAN Circuit [02/2014 - ]
- Check for DTCs and inspect the area that the code indicates.
Result:
B
GO TO DIAGNOSTIC TROUBLE CODE CHART.
Refer to DIAGNOSTIC TROUBLE CODE CHART [02/2014 - ]
Result:
A
See step 8
- Refer to DTC Check / Clear.
- PROBLEM SYMPTOMS TABLE
- Refer to Problem Symptoms Table.
Refer to PROBLEM SYMPTOMS TABLE [02/2014 - ]
Result Proceed to Fault is not listed in Problem Symptoms Table. A Fault is listed in Problem Symptoms Table. B HINT:
If the symptoms do not recur and no DTCs are output, attempt to reproduce the symptoms.
Refer to HOW TO PROCEED WITH TROUBLESHOOTING [02/2014 - 11/2016]
Result:
B
See step 10
Result:
A
See step 9
- Refer to Problem Symptoms Table.
- PERFORM TROUBLESHOOTING BASED ON PROBLEM SYMPTOM
- Refer to Terminals of ECU.
Refer to TERMINALS OF ECU [02/2014 - 11/2016]
Refer to TERMINALS OF ECU [11/2016 - ]
- Refer to Operation Check.
Refer to OPERATION CHECK [02/2014 - ]
Result:
NEXT
See step 10
- Refer to Terminals of ECU.
- CHECK CIRCUIT
- Adjust, repair or replace as necessary.
Result:
NEXT
See step 11
- RECHECK FOR DTC*
- After clearing DTCs, recheck for DTCs.
Refer to DTC CHECK / CLEAR [02/2014 - ]
Body Electrical > Navigation System > Clear DTCs
Body Electrical > Navigation System > Trouble Codes
Result:
NEXT
See step 12
- After clearing DTCs, recheck for DTCs.
- PERFORM CONFIRMATION TEST
Result:
NEXT
END