LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2016 >> Corolla S, Standard Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 6 (Automatic Transmission (U341E) (Service Information)) >> Shift Lever >> Reassembly [08/2013 - 08/2016] >> Procedure

Reassembly [08/2013 - 08/2016]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. HOW TO PREVENT STATIC ELECTRICITY 
    NOTE:
    • Be sure to touch a grounded metal surface with your bare hands to discharge any static electricity before removing or installing the transmission floor shift assembly.
    • Do not touch the electronic components of a circuit board.
    • Keep clothes away from electronic components.
    • Place electronic components removed from the transmission floor shift assembly on SST (anti-static mat).
    1. Wear SST (wrist band).
      GTY477356Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • SST: 09890-47010 
    2. Connect the ground clip of SST (anti-static mat) securely to a ground point provided in the workshop or on a workbench (anchor bolt).
      • SST: 09890-47010 

      HINT: 

      If the ground clip cable is too short, use an extension cable.

    3. Connect the ground clip of the antistatic wrist strap securely to the specified point of the antistatic mat.
  2. INSTALL LOWER POSITION INDICATOR HOUSING 
    1. Engage the 5 claws to install the lower position indicator housing to the shift lock control unit assembly.
      GTY481469Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL INDICATOR LIGHT WIRE SUB-ASSEMBLY 
    1. When replacing the indicator light chip with a new one:
      1. Cut off the top portion of the antistatic bag while retaining enough of the bag to cover a hand.
        GTY472347Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. While holding the sides of the indicator light chip through the antistatic bag, turn the bag inside out.
        GTY472346Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Engage the 2 claws to install the indicator light chip to the lower position indicator housing.
        NOTE:
        • While holding the sides of the indicator light chip through the antistatic bag, install it to the lower position indicator housing.
        • Do not damage the indicator light chip.
        GTY474584Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. When reusing the indicator light chip:
      1. Engage the 2 claws to install the indicator light chip to the lower position indicator housing.
        NOTE:
        • While holding the sides of the indicator light chip, install it to the lower position indicator housing.
        • Do not damage the indicator light chip.
        GTY474584Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Connect terminals 7 and 14 to the transmission control switch connector as shown in the illustration.
      GTY480101Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Mark
    4. Lock the secondary lock.
      GTY472367Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Secondary Lock
    5. Engage the claw to install the clamp to the transmission control switch connector.
      GTY474594Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Engage the clamp to install the indicator light wire sub-assembly to the shift lock control unit assembly.
      GTY473834Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Guide
      *b Clamp
    7. Engage the 2 guides.
    8. Connect the indicator light wire sub-assembly connector.
      GTY474591Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL NO. 2 POSITION INDICATOR SLIDE COVER 
    1. Install the No. 2 position indicator slide cover to the position indicator slide cover.
      GTY474583Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. INSTALL POSITION INDICATOR SLIDE COVER 
    1. Install the position indicator slide cover to the lower position indicator housing.
      GTY474582Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. INSTALL POSITION INDICATOR LIGHT GUIDE 
    1. Engage the 4 claws to install the position indicator light guide to the lower position indicator housing.
      GTY474581Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Do not damage the position indicator light guide.

  7. INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY 
    1. Engage the 4 claws to install the floor shift position indicator housing sub-assembly to the lower position indicator housing.
      GTY481468Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      After installation, check that the indicator light chip illuminates.

scientia non olet · About LEMON Manuals