Engine does not Start because No Initial Combustion [08/2015 - ]: Procedure

1. Clear the DTCs. Refer to DTC CHECK / CLEAR [08/2015 - ] .

NEXT: Go to next step 

1. Check for DTCs. Refer to DTC CHECK / CLEAR [08/2015 - ] .

   Result

   Result	Proceed to
   DTCs are not output	A
   DTCs are output	B

B → See step   13 

A: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / Engine and ECT / Data List.
5. Read the Data List according to the display on the Techstream.
   ENGINE AND ECT (ECM)
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Immobilizer Fuel Cut	Status of immobilizer fuel cut / ON or OFF	-	-

   OK

   OFF is displayed after the ignition switch is turned ON.

   Result

   Result	Proceed to
   NG	A
   OK	B

B → See step   14 

A: Go to next step 

1. Check that the security indicator light turns off when a registered door control transmitter assembly is inserted into the ignition key cylinder.

   OK

   Security indicator light turns off.

   Result

   Result	Proceed to
   NG	A
   OK	B

B → See step   15 

A: Go to next step 

1. Check that the security indicator light turns off when another registered door control transmitter assembly is inserted into the ignition key cylinder.

   OK

   Security indicator light turns off.

NG → See step   7 

OK: Go to next step 

1. Using another registered door control transmitter assembly, turn the ignition switch to ON.
2. Check that the engine starts 5 seconds after the ignition switch was turned to ON.

   OK

   Engine starts normally.

   Result

   Result	Proceed to
   Engine cannot be started	A
   Engine can be started	B

B → See step   11 

A → See step   15 

1. Replace the transponder key coil. Refer to REMOVAL [08/2015 - ] .

NEXT: Go to next step 

1. Using another registered door control transmitter assembly, turn the ignition switch to ON.
2. Check that the engine starts 5 seconds after the ignition switch was turned to ON.

   OK

   Engine starts normally.

   Result

   Result	Proceed to
   Engine can be started	A
   Engine cannot be started	B

B → See step   9 

A → END (TRANSPONDER KEY COIL WAS DEFECTIVE) 

1. Replace the transponder key ECU assembly with a new one. Refer to REMOVAL [08/2015 - ] .
   NOTE:

   Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to Registration. Refer to REGISTRATION [08/2015 - ] .

NEXT: Go to next step 

1. Using another registered door control transmitter assembly, turn the ignition switch to ON.
2. Check that the engine starts 5 seconds after the ignition switch was turned to ON.

   OK

   Engine starts normally.

   Result

   Result	Proceed to
   Engine can be started	A
   Engine cannot be started	B

B → See step   11 

A → END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE) 

1. Replace the door control transmitter assembly.
   NOTE:

   Key ID code registration is necessary when replacing the door control transmitter assembly, refer to Registration. Refer to REGISTRATION [08/2015 - ] .

NEXT: Go to next step 

1. Using another registered door control transmitter assembly, turn the ignition switch to ON.
2. Check that the engine starts 5 seconds after the ignition switch was turned to ON.

   OK

   Engine starts normally.

   Result

   Result	Proceed to
   Engine can be started	A
   Engine cannot be started	B

B → See step   14 

A → END (DOOR CONTROL TRANSMITTER ASSEMBLY WAS DEFECTIVE)