LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2016 >> Avalon XLE >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Supplemental Restraint System - Diagnostic Codes & Symptom Tests - (Except Hybrid) >> Airbag System >> DTC B1625/22: Side Airbag Sensor LH Circuit Malfunction [10/2014 - ] >> Procedure

DTC B1625/22: Side Airbag Sensor LH Circuit Malfunction [10/2014 - ]: Procedure

  1. CHECK CONNECTORS 
    1. Turn the engine switch off.
    2. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag ECU assembly, side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.

      OK

      The connectors are properly connected.

      HINT: 

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag ECU assembly, side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.
    5. Check that the terminals of the connectors are not damaged.

      OK

      The terminals are not deformed or damaged.

    Result: 

    NG 

    REPLACE FLOOR WIRE 

    Result: 

    OK 

    See step  2

  2. CHECK FLOOR WIRE (OPEN) 
    1. Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.
      GTY609027Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Side Airbag Sensor Assembly LH
      *2 Airbag ECU Assembly
      *3 Floor Wire
      *4 Service Wire
      *a Front view of wire harness connector
      (to Airbag ECU Assembly)
      *b Front view of wire harness connector
      (to Side Airbag Sensor Assembly LH)
      NOTE:

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J6-4 (BBL+) -J6-3 (BBL-) Always Below 1 Ω
    3. Disconnect the service wire from connector B.

    Result: 

    NG 

    REPLACE FLOOR WIRE 

    Result: 

    OK 

    See step  3

  3. CHECK FLOOR WIRE (SHORT) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY607771Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Side Airbag Sensor Assembly LH
      *2 Airbag ECU Assembly
      *3 Floor Wire
      *a Front view of wire harness connector
      (to Side Airbag Sensor Assembly LH)

      Standard Resistance

      Tester Connection Condition Specified Condition
      J6-4 (BBL+) - J6-3 (BBL-) Always 1 MΩ or higher

    Result: 

    NG 

    REPLACE FLOOR WIRE 

    Result: 

    OK 

    See step  4

  4. CHECK FLOOR WIRE (SHORT TO B+) 
    1. Connect the cable to the negative (-) battery terminal.
      GTY607771Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Side Airbag Sensor Assembly LH
      *2 Airbag ECU Assembly
      *3 Floor Wire
      *a Front view of wire harness connector
      (to Side Airbag Sensor Assembly LH)
    2. Turn the engine switch on (IG).
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      J6-4 (BBL+) - Body ground Engine switch on (IG) Below 1 V
      J6-3 (BBL-) - Body ground Engine switch on (IG) Below 1 V
    4. Turn the engine switch off.
    5. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Result: 

    NG 

    REPLACE FLOOR WIRE 

    Result: 

    OK 

    See step  5

  5. CHECK FLOOR WIRE (SHORT TO GROUND) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY607771Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Side Airbag Sensor Assembly LH
      *2 Airbag ECU Assembly
      *3 Floor Wire
      *a Front view of wire harness connector
      (to Side Airbag Sensor Assembly LH)

      Standard Resistance

      Tester Connection Condition Specified Condition
      J6-4 (BBL+) - Body ground Always 1 MΩ or higher
      J6-3 (BBL-) - Body ground Always 1 MΩ or higher

    Result: 

    NG 

    REPLACE FLOOR WIRE 

    Result: 

    OK 

    See step  6

  6. CHECK FLOOR WIRE (OPEN) 
    1. Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.
      GTY546836Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly LH
      *3 Floor Wire
      *4 Service Wire
      *a Front view of wire harness connector
      (to Side Airbag Sensor Assembly LH)
      *b Front view of wire harness connector
      (to Side No. 2 Airbag Sensor Assembly LH)
      NOTE:

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      J6-1 (BCL+) - J6-2 (BCL-) Always Below 1 Ω
    3. Disconnect the service wire from connector C.

    Result: 

    NG 

    REPLACE FLOOR WIRE 

    Result: 

    OK 

    See step  7

  7. CHECK FLOOR WIRE (SHORT) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY581776Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly LH
      *3 Floor Wire
      *a Front view of wire harness connector
      (to Side Airbag Sensor Assembly LH)

      Standard Resistance

      Tester Connection Condition Specified Condition
      J6-1 (BCL+) - J6-2 (BCL-) Always 1 MΩ or higher

    Result: 

    NG 

    REPLACE FLOOR WIRE 

    Result: 

    OK 

    See step  8

  8. CHECK FLOOR WIRE (SHORT TO B+) 
    1. Connect the cable to the negative (-) battery terminal.
      GTY581776Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly LH
      *3 Floor Wire
      *a Front view of wire harness connector
      (to Side Airbag Sensor Assembly LH)
    2. Turn the engine switch on (IG).
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      J6-1 (BCL+) - Body ground Engine switch on (IG) Below 1 V
      J6-2 (BCL-) - Body ground Engine switch on (IG) Below 1 V
    4. Turn the engine switch off.
    5. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Result: 

    NG 

    REPLACE FLOOR WIRE 

    Result: 

    OK 

    See step  9

  9. CHECK FLOOR WIRE (SHORT TO GROUND) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY581776Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly LH
      *3 Floor Wire
      *a Front view of wire harness connector
      (to Side Airbag Sensor Assembly LH)

      Standard Resistance

      Tester Connection Condition Specified Condition
      J6-1 (BCL+) - Body ground Always 1 MΩ or higher
      J6-2 (BCL-) - Body ground Always 1 MΩ or higher

    Result: 

    NG 

    REPLACE FLOOR WIRE 

    Result: 

    OK 

    See step  10

  10. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH 
    1. Connect the connectors to the side No. 2 airbag sensor assembly LH and airbag ECU assembly.
      GTY381346Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Side Airbag Sensor Assembly RH
      *2 Airbag ECU Assembly
    2. Interchange the side airbag sensor assembly LH with RH and connect the connectors.
    3. Connect the cable to the negative (-) battery terminal.
    4. Clear the DTCs stored in memory (Refer to DTC CHECK / CLEAR [10/2014 - ] ).
    5. Turn the engine switch off.
    6. Turn the engine switch on (IG), and wait for at least 60 seconds.
    7. Check for DTCs (Refer to DTC CHECK / CLEAR [10/2014 - ] ).

      Result

      Result Proceed to
      DTC B1625/22 is output. A
      DTC B1620/21 is output. B
      DTCs B1620/21 and B1625/22 are not output. C

      HINT: 

      Codes other than DTCs B1620/21 and B1625/22 may be output at this time, but they are not related to this check.

    8. Turn the engine switch off.
    9. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    10. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.

    Result: 

    B 

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    C 

    USE SIMULATION METHOD TO CHECK 

    (Refer to HOW TO PROCEED WITH TROUBLESHOOTING [10/2014 - 10/2015] or HOW TO PROCEED WITH TROUBLESHOOTING [10/2015 - ] )

    Result: 

    A 

    See step  11

  11. CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH 
    1. Disconnect the connector from the side No. 2 airbag sensor assembly LH.
      GTY542576Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly LH
    2. Connect the cable to the negative (-) battery terminal.
    3. Clear the DTCs stored in memory (Refer to DTC CHECK / CLEAR [10/2014 - ] ).
    4. Turn the engine switch off.
    5. Turn the engine switch on (IG), and wait for at least 60 seconds.
    6. Check for DTCs (Refer to DTC CHECK / CLEAR [10/2014 - ] ).

      OK

      DTC B1625/22 is not output.

      HINT: 

      Codes other than DTC B1625/22 may be output at this time, but they are not related to this check.

    Result: 

    OK 

    REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    NG 

    REPLACE AIRBAG ECU ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

scientia non olet · About LEMON Manuals