LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2016 >> Avalon XLE >> Repair and Diagnosis >> Accessories & Equipment >> Interior/Illumination Lights >> Lighting System - Diagnostics & Circuit Tests - (Except Hybrid) >> Lighting System >> Circuit Tests >> Door Unlock Detection Switch Circuit [10/2014 - ] >> Procedure

Door Unlock Detection Switch Circuit [10/2014 - ]: Procedure

  1. READ VALUE USING TECHSTREAM 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Main Body / Data List.
    5. Read the Data List according to the display on the Techstream.
      MAIN BODY

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      FR Door Lock Pos Front door RH unlock detection switch signal/LOCK or UNLOCK LOCK: Front door RH locked
      UNLOCK: Front door RH unlocked      		 -
      FL Door Lock Pos Front door LH unlock detection switch signal/LOCK or UNLOCK LOCK: Front door LH locked
      UNLOCK: Front door LH unlocked      		 -
      RR-Door Lock Pos SW Rear door RH unlock detection switch signal/ON or OFF ON: Rear door RH unlocked
      OFF: Rear door RH locked      		 When checking this item, make sure to check it with the rear door LH locked.
      RL-Door Lock Pos SW Rear door LH unlock detection switch/ON or OFF ON: Rear door LH unlocked
      OFF: Rear door LH locked      		 When checking this item, make sure to check it with the rear door RH locked.

      Result

      Result Proceed to
      OK A
      "FL Door Lock Pos" is not normal B
      "FR Door Lock Pos" is not normal C
      "RR-Door Lock Pos SW" or "RL-Door Lock Pos SW" is not normal D

    Result: 

    A 

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE 

    (Refer to PROBLEM SYMPTOMS TABLE [10/2014 - ] )

    Result: 

    C 

    See step  4

    Result: 

    D 

    See step  6

    Result: 

    B 

    See step  2

  2. INSPECT FRONT DOOR LOCK ASSEMBLY LH 
    1. Remove the front door lock assembly LH (Refer to REMOVAL [10/2014 - ] ).
    2. Inspect the front door lock assembly LH (Refer to INSPECTION [10/2014 - ] ).

      OK

      Front door lock assembly LH is normal.

    Result: 

    NG 

    REPLACE FRONT DOOR LOCK ASSEMBLY LH 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY LH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND) 
    1. Disconnect the D6 main body ECU (multiplex network body ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G1-8 (LSSR) - D6-7 (LSFL) Always Below 1 Ω
      G1-8 (LSSR) - Body ground Always 10 kΩ or higher
      G1-7 (E) - Body ground Always Below 1 Ω

    Result: 

    OK 

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  4. INSPECT FRONT DOOR LOCK ASSEMBLY RH 
    1. Remove the front door lock assembly RH (Refer to REMOVAL [10/2014 - ] ).
    2. Inspect the front door lock assembly RH (Refer to INSPECTION [10/2014 - ] ).

      OK

      Front door lock assembly RH is normal.

    Result: 

    NG 

    REPLACE FRONT DOOR LOCK ASSEMBLY RH 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND) 
    1. Disconnect the D6 main body ECU (multiplex network body ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      F1-7 (LSSR) - D6-18 (LSFR) Always Below 1 Ω
      F1-7 (LSSR) - Body ground Always 10 kΩ or higher
      F1-8 (E) - Body ground Always Below 1 Ω

    Result: 

    OK 

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  6. CHECK DATA LIST 

    Result

    Result Proceed to
    "RL-Door Lock Pos SW" is not normal A
    "RR-Door Lock Pos SW" is not normal B
    "RR-Door Lock Pos SW" and "RL-Door Lock Pos SW" is not normal C

    Result: 

    B 

    See step  10

    Result: 

    C 

    See step  13

    Result: 

    A 

    See step  7

  7. INSPECT REAR DOOR LOCK ASSEMBLY LH 
    1. Remove the rear door lock assembly LH (Refer to REMOVAL [10/2014 - ] ).
    2. Inspect the rear door lock assembly LH (Refer to INSPECTION [10/2014 - ] ).

      OK

      Rear door lock assembly LH is normal.

    Result: 

    NG 

    REPLACE REAR DOOR LOCK ASSEMBLY LH 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    OK 

    See step  8

  8. CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND) 
    1. Disconnect the 3C instrument panel junction block assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I1-6 (LSSR) - 3C-17 Always Below 1 Ω
      I1-6 (LSSR) - Body ground Always 10 kΩ or higher
      I1-9 (E) - Body ground Always Below 1 Ω

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  9

  9. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 
    1. Remove the instrument panel junction block assembly (Refer to REMOVAL [10/2014 - ] ).
    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
    3. Measure the resistance according to the value(s) in the table below.
      GTY560850Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Instrument Panel Junction Block Assembly)      		 - -

      Standard Resistance

      Tester Connection Condition Specified Condition
      3C-17 - MB-5 (LSR) Always Below 1 Ω

    Result: 

    OK 

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    NG 

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

  10. INSPECT REAR DOOR LOCK ASSEMBLY RH 
    1. Remove the rear door lock assembly RH (Refer to REMOVAL [10/2014 - ] ).
    2. Inspect the rear door lock assembly RH (Refer to INSPECTION [10/2014 - ] ).

      OK

      Rear door lock assembly RH is normal.

    Result: 

    NG 

    REPLACE REAR DOOR LOCK ASSEMBLY RH 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    OK 

    See step  11

  11. CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND) 
    1. Disconnect the 3A instrument panel junction block assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      H1-6 (LSSR) - 3A-53 Always Below 1 Ω
      H1-6 (LSSR) - Body ground Always 10 kΩ or higher
      H1-9 (E) - Body ground Always Below 1 Ω

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  12

  12. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 
    1. Remove the instrument panel junction block assembly (Refer to REMOVAL [10/2014 - ] ).
    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
    3. Measure the resistance according to the value(s) in the table below.
      GTY573445Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Instrument Panel Junction Block Assembly)      		 - -

      Standard Resistance

      Tester Connection Condition Specified Condition
      3A-53 - MB-5 (LSR) Always Below 1 Ω

    Result: 

    OK 

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    NG 

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

  13. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 
    1. Remove the instrument panel junction block assembly (Refer to REMOVAL [10/2014 - ] ).
    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
    3. Measure the resistance according to the value(s) in the table below.
      GTY572719Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Instrument Panel Junction Block Assembly)      		 - -

      Standard Resistance

      Tester Connection Condition Specified Condition
      3C-17 - MB-5 (LSR) Always Below 1 Ω
      3A-53 - MB-5 (LSR) Always Below 1 Ω

    Result: 

    OK 

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 

    (Refer to REMOVAL [10/2014 - ] )

    Result: 

    NG 

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 

    (Refer to REMOVAL [10/2014 - ] )

scientia non olet · About LEMON Manuals