LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2016 >> 4Runner Limited, AWD >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Airbag System - Diagnostic Codes (B1690-B1905) & Symptom Tests >> Airbag System >> DTC B1900: Short in P/T Squib (RH) Circuit; DTC B1901: Open in P/T Squib (RH) Circuit; DTC B1902: Short in P/T Squib (RH) Circuit (to Ground); DTC B1903: Short in P/T Squib (RH) Circuit (to +B) [08/2019 - ] >> Procedure

DTC B1900: Short in P/T Squib (RH) Circuit; DTC B1901: Open in P/T Squib (RH) Circuit; DTC B1902: Short in P/T Squib (RH) Circuit (to Ground); DTC B1903: Short in P/T Squib (RH) Circuit (to +B) [08/2019 - ]: Procedure

  1. CHECK FRONT SEAT OUTER BELT RH (FRONT PRETENSIONER SQUIB RH) 
    1. Turn the ignition switch off.
      GTY722217Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
    3. Disconnect the connectors from the front seat outer belt RH.
    4. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.
      WARNING:

      Never connect the tester to the front seat outer belt RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

      NOTE:
      • Do not forcibly insert SST into the terminals of the connector when connecting SST.
      • Insert SST straight into the terminals of the connector.
      • SST: 09843-18061 
    5. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
    6. Turn the ignition switch to ON, and wait for at least 60 seconds.
    7. Clear the DTCs (Refer to DTC CHECK / CLEAR [08/2019 - ] ).
    8. Turn the ignition switch off.
    9. Turn the ignition switch to ON, and wait for at least 60 seconds.
    10. Check for DTCs (Refer to DTC CHECK / CLEAR [08/2019 - ] ).

      OK

      DTC B1900, B1901, B1902 or B1903 is not output.

      HINT: 

      Codes other than DTC B1900, B1901, B1902 and B1903 may be output at this time, but they are not related to this check.

      TEXT IN ILLUSTRATION

      *1 Front Pretensioner Squib RH
      *2 Airbag Sensor Assembly
      *3 Connector C
      *4 SST
      *a Front view of wire harness connector
      (to Front Pretensioner Squib RH)

    Result: 

    OK 

    REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH 

    (Refer to REMOVAL [08/2015 - ] )

    Result: 

    NG 

    See step  2

  2. CHECK CONNECTOR 
    1. Turn the ignition switch off.
    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
    3. Disconnect SST from connector C.
    4. Check that the floor wire connector (on the front seat outer belt RH side) is not damaged.

      OK

      The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

      GTY646273Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Front Pretensioner Squib RH
      *2 Airbag Sensor Assembly

    Result: 

    NG 

    REPLACE FLOOR WIRE 

    Result: 

    OK 

    See step  3

  3. CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT) 
    1. Disconnect the connectors from the airbag sensor assembly.
      GTY727389Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      N4-1 (R+) - Body ground Ignition switch ON Below 1 V
      N4-2 (R-) - Body ground Ignition switch ON Below 1 V
    4. Turn the ignition switch off.
    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      N4-1 (R+) - N4-2 (R-) Always Below 1 Ω
    7. Release the activation prevention mechanism built into connector B (Refer to DIAGNOSIS SYSTEM [08/2019 - ] ).
    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      N4-1 (R+) - N4-2 (R-) Always 1 MΩ or higher
      N4-1 (R+) - Body ground Always 1 MΩ or higher
      N4-2 (R-) - Body ground Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Front Pretensioner Squib RH
      *2 Floor Wire
      *3 Airbag Sensor Assembly
      *4 Connector C
      *a Front view of wire harness connector
      (to Front Pretensioner Squib RH)

    Result: 

    NG 

    REPLACE FLOOR WIRE 

    Result: 

    OK 

    See step  4

  4. CHECK AIRBAG SENSOR ASSEMBLY 
    1. Connect the connectors to the front seat outer belt RH and airbag sensor assembly.
      GTY719520Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
    3. Turn the ignition switch to ON, and wait for at least 60 seconds.
    4. Clear the DTCs stored in memory (Refer to DTC CHECK / CLEAR [08/2019 - ] ).
    5. Turn the ignition switch off.
    6. Turn the ignition switch to ON, and wait for at least 60 seconds.
    7. Check for DTCs (Refer to DTC CHECK / CLEAR [08/2019 - ] ).

      OK

      DTC B1900, B1901, B1902 or B1903 is not output.

      HINT: 

      Codes other than DTC B1900, B1901, B1902 and B1903 may be output at this time, but they are not related to this check.

      TEXT IN ILLUSTRATION

      *1 Front Pretensioner Squib RH
      *2 Airbag Sensor Assembly

    Result: 

    OK 

    USE SIMULATION METHOD TO CHECK 

    (Refer to DIAGNOSIS SYSTEM [08/2019 - ] )

    Result: 

    NG 

    REPLACE AIRBAG SENSOR ASSEMBLY 

    (Refer to REMOVAL [08/2015 - ] )

scientia non olet · About LEMON Manuals